JVC GR-DVF20, LYT0244-001A manual Power, Charging the Battery Pack, Using the Battery Pack

Page 8

8EN

Marks

To AC outlet

CHARGE indicator

REFRESH switch

REFRESH indicator

REFRESH

The AC Power Adapter/Charger features a REFRESH function that allows you to fully discharge the battery pack before recharg- ing.

Perform the REFRESH function after no less than 5 chargings.

To discharge the battery . . .

.... attach the battery pack to the adapter as

shown in the above illustration. Then push REFRESH. The REFRESH indicator lights when discharging starts, and goes out when discharging is complete.

GETTINGSTARTED

Power

This camcorder’s 3-way power supply system lets you choose the most appropriate source of power.

NOTES:

●No function is available without power supply.

●Use only specified power supply.

●Do not use provided power supply units with other equipment.

CHARGING THE BATTERY PACK

1 SUPPLY POWER

Connect the charger’s AC power cord to a wall outlet.

2 ATTACH BATTERY PACK

Align the marks and slide the battery pack in the direction of the arrow until it locks in place.

•The CHARGE indicator begins blinking to indicate charging has started.

DETACH BATTERY PACK

 

3 When the CHARGE indicator stops blinking but stays

lit, charging is finished. Slide the battery pack

opposite the direction of the arrow.

 

 

 

 

Battery pack

Charging time

 

Discharging time

 

 

 

 

BN-V12U

approx. 1 hr. 10 min.

 

approx. 3 hrs. 30 min.

 

 

 

 

BN-V20U

approx. 1 hr. 50 min

 

approx. 6 hrs. 40 min.

 

 

 

 

AHook on.

B Push in.

BATTERY RELEASE

ATTENTION:

Before detaching the power source, make sure that the camcorder’s power is turned off. Failure to do so can result in a camcorder malfunction.

USING THE BATTERY PACK

1 ATTACH BATTERY PACK

Hook its end to the camcorder ( A ) and push the battery pack in until it locks in place ( B ) .

DETACH BATTERY PACK

 

2 Slide BATTERY RELEASE and pull out the battery

pack.

 

 

 

 

Approximate recording time (unit: min.)

 

 

 

 

 

 

 

LCD

LCD

 

LCD

Battery

monitor on/

monitor off/

monitor on/

pack

Viewfinder off

Viewfinder on

Viewfinder on

BN-V12U

50 (35)

60

(35)

45 (30)

BN-V20U

90 (55)

100

(60)

80 (50)

 

 

 

 

 

( ) : when the video light is on.

INFORMATION:

VU-V856KIT is a set composed of the BN-V856U battery pack and AA-V80U AC Power Adapter/Charger.

The BN-V856U battery pack provides approx. 7 hours of recording time when the viewfinder is on and the LCD monitor and the video light are off. Also read thoroughly the VU-V856KIT's instruction manuals.

It is impossible to charge the BN-V856U battery pack using the provided AC Power Adapter/Charger. Use the optional AA-V80U AC Power Adapter/Charger.

Page 7 Page 9
Image 8
Page 7 Page 9
Contents GR-DVF20 For Customer UseIt is recommended that you For clock operation and remote control unitDear Customer EN3 Accessories CleaningDamage Requiring Service Replacement Parts Battery Pack EN5 About Batteries Min DVM-30ITI Insert and Tracking Information Area Sub-Code AreaVideo Area Audio Area Contents Using the Battery Pack PowerCharging the Battery Pack Charge Marker Using AC PowerUsing a CAR Battery Clock Lithium Battery Insertion/Removal Insert Battery in Holder10 EN RE-INSERT HolderDate/Time Settings EN1112 EN Loading/Unloading a CassetteEN13 Recording Mode SettingSET Recording Mode 14 EN Grip AdjustmentViewfinder Adjustment EN15 Shoulder Strap AttachmentTripod Mounting Power Switch Position 16 ENRecording Basic Recording Shooting While Watching The ViewfinderEN17 Stop RecordingPress Display Button RecordingBefore the following steps, perform pg 18 ENShooting While Watching The LCD Monitor Journalistic Shooting Interface ShootingBrightness Control EN19Feature Picture Stabilizer 20 ENBasic Recording ZoomFeature Video Light To brighten the scene when natural lighting is too dimBattery power EN21Basic Features When blank portion is recorded on a tapeTime Code Recording From The Middle Of a TapeRecording Advanced Features EN23 Displaying The Date And Time During RecordingSelect Function SET Function ParametersAdvanced Features Snapshot Mode Selection24 EN SnapshotMotor Drive Mode EN25Using Menu For Detailed Adjustment Make SettingEND Setting Select Function Parameters in DATE/TIME Menu or System MenuRecording Menu Explanations Factory-presetEN27 Date/Time Menu Explanations System Menu ExplanationsFade/Wipe Effects EN29Effect Selection FADE/WIPE Selection30 EN Picture Wipe or Dissolve Selection P, P, P, P , P, P and PBefore the following steps, perform steps 1 through 3 on pg If you select Picture Wipe/Dissolve during recordingMenu Effect EN31Fader And Wipe Menu Recording Advanced Features Select ModeDisable Mode 32 ENSlow Slow Shutter EN33Focusing When shooting a scene with a high-contrast background34 EN Auto FocusEN35 Manual FocusAccess Exposure Control 36 ENExposure Control To darken the imageIris Lock EN37Center SUBJECT, Lock Iris IrisWhite Balance Adjustment Accessment White Balance Adjust38 EN To Return To Automatic White BalanceEnter Setting Manual White Balance OperationEN39 Exit Manual White Balance AD- JustmentSpeaker Volume Control 40 ENPlayback Basic Playback Rewind or Fast-forward the tapeFeature Still Playback Feature Shuttle SearchFeature Slow-Motion Playback Feature Playback ZoomPlayback Advanced Features Access Playback Menu42 EN Playback MenuPlayback Sound Displaying the Date During PlaybackEN43 Displaying The Time Code During PlaybackConnections Connectors44 EN Connectinput VCR Output to TV Supply Power EN45Connectvcr Camcorder to TV or Turn on the camcorder, the VCR and the TV46 EN Tape DubbingInstalling The Battery EN47Buttons 48 ENFunctions To stop Slow-Motion Playback in progess, press Play EN49To allow slow-speed search in either direction Playback Zoom Activate ZoomEND Zoom DownAccessmenu Playback Effect Select Playback Special EffectsEN51 Start Playback52 EN Random Assemble Editing R.A.EditSET REMOTE/VCR Code Operate VCREN53 Jlip54 EN Select ScenesUSE FADE/WIPE on Scene Transition if Necessary USE Program AE with Special Effects if NecessaryEN55 Automatic Editing to VCRPrepare Source Tape Stop EditingDiagnosing VCR’S Against Camcorder Timing 56 ENFor More Accurate Editing Input Correction Data Adjustment of VCR’S Against Camcorder TimingEN57 58 EN Corrective ActionVideo mode Video playback Set the Power Switch to Effects and Fade/WipeSelected the mode For editing was registered Completed pg Being used in a scene60 EN Recording Menu Use the Picture Wipe Function pgIndicators On Screen is set to Set on Screen to on OFF in the Date/Time Date/Time Menu ScreenWhitish Become hot62 EN Open the lens cover pg Close the LCD monitorClean Exterior Clean LCD MonitorClean Lens After Use64EN # $ y %Connectors IndicatorsControls Other Parts66 EN IndicationsLCD Monitor/Viewfinder Indications During Recording FunctionIndications Function LCD Monitor/Viewfinder Indications During PlaybackEN67 68 EN To prevent damage and prolong service life EN69To avoid hazard During useFor safety, do not Avoid using the unitTo prolong service life To prevent damage to the LCD monitor, do notAC Power Adapter/Charger AA-V15U ConnectorsCamcorder EN71GR-DVF20
Top Page Image Contents