JVC 0797TOV*UN*SN Date/Time Settings, Select Operation Mode, Input Date and Time, LCD monitor

Page 11

EN 11

Date/Time Settings

Date and time will automatically be recorded on tape at all times. It is your choice to display it or not during playback (☞ pg. 52).

To set date and time follow the instructions from 1 to 5.

LCD monitor

REC MODE

SP

WIDE MODE

OFF

ZOOM

20X

DIS

ON

GAIN UP

AGC

FLASH

AUTO

4TO DATE / TIME MENU TO SYSTEM MENU

END

Recording Menu

 

ON SCREEN

OFF

 

DISPLAY

ON

4

DATE / TIME

1 . 1 . 00

 

 

0 : 00

RETURN

Date/Time Menu

MENU

Lock button

Power Dial

Power lamp

5S

 

M

OFFYA

 

A

P

 

 

 

L

Select Dial

MENU button

1 SELECT OPERATION MODE

Set the Power Dial to “ M ” while pressing down the lock button located on the dial, and open the LCD monitor fully.

•The power lamp comes on and the camcorder is turned on.

•The LCD monitor can be tilted upward up to 180 degrees and downward up to 90 degrees.

2 ACCESS RECORDING MENU Press MENU. The Recording Menu appears.

3 ACCESS DATE/TIME MENU Move the pointer and highlight bar to “TO DATE/TIME MENU” by rotating the Select Dial. Press the Select Dial and the Date/Time Menu appears.

4 INPUT DATE AND TIME

Move the pointer and highlight bar to “DATE/ TIME” by rotating the Select Dial. Press the Select Dial and “day” is highlighted and begins blinking.

Rotating the Select Dial (rotate it upward to increase and downward to decrease), input the day. Press the Select Dial. Repeat the procedure to input the month, year, hour and minute.

•Press the Select Dial twice when the pointer and highlight bar are set to “RETURN” to exit.

Regarding Built-in Rechargeable Battery

To store the date/time in memory, a rechargeable clock lithium battery is integrated in the camcorder. While the camcorder is connected to an AC outlet using the AC Power Adapter/Charger, or while the battery pack installed in the camcorder continues to supply power to the camcorder, the clock lithium battery is always charged. However, if the camcorder is not used for approx. 3 months, the clock lithium battery will become discharged and the date/time stored in memory will be lost. When this occurs, first connect the camcorder to an AC outlet using the AC Power Adapter/Charger etc. for over 24 hours to charge the clock lithium battery. Then perform the date/time setting before using the camcorder.

It is also possible to use the camcorder without the date/time setting.

NOTE:

If you don’t exit the Date/Time Menu, the clock display will not move but the camcorder’s internal clock continues to operate. Once you close the menu, the date and time begin operation from the current date and time, with no delay or loss.

Page 10 Page 12
Image 11
Page 10 Page 12
Contents GR-DVX It is recommended that you Dear CustomerSafety Precautions DC cord EN P Rovided a CCE SsoriesDV30ME Remote control unit RM-V711ULithium battery CR2025 For remote control unitITI Insert and Tracking Information Area Sub-Code AreaVideo Area Audio Area Contents Detach Charging The Battery PackDetach BATTERY/BATTERIES AttachClose Battery Cover Installing The Battery PackOpen Battery Cover Insert BatteryKnob and insert Supply PowerFirst. Close the battery cover Attach to CamcorderLCD monitor Date/Time SettingsSelect Operation Mode Input Date and TimeINSERT/REMOVE Tape OPEN/EJECT switchLoading/Unloading a Cassette Open Cassette CoverSet depending on your preference Recording Mode SettingSET Recording Mode During transporting Attach Hand StrapPUT Camcorder Close FlapAttach Grip Strap to Hand Strap Eyelet Adjust LengthGrip Strap Attachment Tripod MountingTurn on Camcorder Dioptre AdjustmentAdjust Dioptre Insert Battery in Holder Remote Control UnitInstalling The Battery Pull OUT Battery HolderPower Dial Position Function Operation ModeStop Recording Basic RecordingPull OUT Viewfinder or Open LCD Monitor Start RecordingStart Search Engage Still ModeRecording From The Middle Of a Tape During shooting When blank portion is recorded on a tapeTime Code Proper recordingBrightness indication appears in the LCD monitor Tape Remaining IndicatorAdjust Brightness Brightness ControlTilt LCD Monitor Journalistic shootingInterface Shooting Open LCD MonitorZoom RE COR DIN GTake Snapshot Motor Drive modeChanging the Snapshot Setting SnapshotSelect Function Snapshot Flash Auto FlashAccess Flash Adjustment Adjusting Flash BrightnessSelect Mode Accessmenu Manual Mode ItemScene 5-second recording Engage 5S ModeDissolves during 5 second mode recording To Take a Snapshot In The 5-Second ModeTo Take a Snapshot In The Self-Timer Mode Self-TimerStop SELF-TIMER Recording END SELF-TIMER RecordingPlease refer to page 31, 32 for details MenusClose Recording Menu Recording Menu allows you to set these functionsWide Mode REC Mode Recording modeFlash pg Zoom Zoom magnificationDIS Digital Image Stabilizer Displaying The Date And Time During Recording Close System Menu Access System MenuSystem Menu Return Sound signals can be sampled at 32 kHz or 48 kHzSelect Effect Access FADER/WIPE MenuTo Cancel FADE/WIPE Effects FADE/WIPE EffectsFader White Fades and WipesExample WH ExampleP and P of the Fader/Wipe Menu Picture Wipe/DissolveResume Recording Random Variations Fade in or out with a full-screen mosaic effect Fade in or out with a white screenFade in or out with a black screen Fade out from colour to black and whiteRight corner to the lower left corner New scene gradually appears as the old one graduallyDisappears New scene wipes in over the previous one from the upperAE/Effects Disable P.AE/EFFECTSepia Classic FilmStrobe TwilightTo Change To Auto Focus Manual Focus AdjustmentAccess Manual Focus Adjust FocusTo Return To Automatic Exposure Control Adjust ExposureExposure Control Brightness control of the LCD monitorIris After , adjust the exposure rotatingIris Lock To Return To Automatic Iris ControlSelect Auto in . Or set the Power Dial to White Balance AdjustmentAccessment White Balance Adjust Closement White Balance AdjustTo Change The Tint For Recording Enter SettingExit Manual White Balance Adjustment Manual White Balance OperationEND Playback Volume switchRewind Tape Viewing RecordingEND Zoom Playback ZoomActivate Zoom Locatescene Portion of MagnifiedStart Playback Press the Play button Playback EffectsSelect P.AE/EFFECT RM-V711UPlayback Menu allows you to set the following functions Access Playback MenuPlayback Menu Close MenuDisplaying The Time Code During Playback Playback SoundDisplaying the Date During Playback Turn the Power Dial to Play and turn on the TV/VCR VCR/TV Connection when connecting directly to the camcorderTurn on Power Select TV’S Video ModeAttach and Locks VCR/TV Connection using Docking StationConfirm POWER-OFF Status Supply Power Video OUT VCR/TV connection using the Docking StationConnect Docking Station to TV or VCR Connection to a TV or VCREquipped with an S-VIDEO And/or A/V input RCAVCR Recording deck DubbingMake Connections Start Playback Pause RecordingRM-V711U 9 ` provided Brand SettingOperate the VCR VCR Code List Execute FADE/WIPE in if Necessary Random Assemble EditingMake Connections Start Source PlaybackUSE P.AE/EFFECT if Necessary SET EDIT-IN PointSET EDIT-OUT Point USE Fade Wipe on Scene Transition if NecessaryButton Engagemode Vcrs RECORD-PAUSEStart Editing Stop EditingChoose a Scene For More Accurate EditingPrepare for R.A. Edit Play Back Dubbed Scene Press MENU. The Playback Menu appears on the TV screen Input Correction DataPause During Dubbing Audio DubbingFind EDIT-IN Point Begin DubbingPause During Editing Insert EditingFind Edit OUT Point Find Edit in PointReplace with new cassette Battery pg5S or Tape END appearsEN TR Ouble Shooting Picture Wipe function doesn’t work Squeeze or Cinema mode is selected in the Recording MenuEnd of its service life, images Same time Cleaning The Camcorder Camcorder IND.ON/OFF button pg OPEN/EJECT switch pgPower dial pg RBATTERY cover pgDocking Station Brightness of the flash LCD Monitor/Viewfinder Indications During RecordingFunction Appears during recording Appears while the tape is runningLCD Monitor/Viewfinder Indications During Playback Indications Function To prevent damage to the camcorder For safety, do notAvoid using the unit To avoid hazardTo prevent damage to the LCD monitor, do not To prolong service lifeDo not leave the unit To protect the unit, do notVideo signal recording format PowerPower consumption Signal formatOn-screen display Colour temperatureAC Adapter Auto focusAnimation Audio Dubbing Second Mode Fade-In/OutLithium Battery Pg , 3 Motor Drive ModeGR-DVX
Top Page Image Contents