JVC LYT0672-001A, 1000MKV*UN*VP specifications 48EN

Page 48

48EN

TROUBLESHOOTING

If, after following the steps in the chart below, the problem still exists, please consult your JVC dealer.

The camcorder is a microcomputer-controlled device. External noise and interference (from a TV, a radio, etc.) might prevent it from functioning properly. In such cases, first disconnect its power supply unit (battery pack, AC Adapter, etc.); and then re-connect it and proceed as usual from the beginning.

SYMPTOM

POWER

No power is supplied.

POSSIBLE CAUSE(S)

The battery pack has not been attached correctly ( pg. 6).

The battery pack is not charged ( pg. 6).

The power supply has not been correctly connected ( pg. 6, 7).

The power suddenly goes off and does not come back on by itself.

The battery pack has completely discharged.

Remove the cassette and disconnect the power source, then after a few minutes, try turning the power back on. If it still does not come on, consult your nearest JVC dealer.

RECORDING

Recording cannot be performed.Make sure the Erase Protection tab is in the position that allows recording. If not, slide the tab. Some cassettes have removable tabs. If the tab has been removed, cover the hole with adhesive tape ( pg. 13).

Recording does not start.

The camcorder Power Switch has not been set to “ ” or

” ( pg. 14).

Animation or Time-Lapse is not

Before recording in the Animation mode at the very

available.

beginning of a tape, set the camcorder to the Recording

 

mode for about 5 seconds, so that the tape runs smoothly.

 

Using the Fade-in function at this point is a good way to

 

begin an animated programme ( pg. 26, 37).

 

 

PLAYBACK

 

The tape is running, but there is no

The TV has not been set to its VIDEO mode or channel.

playback picture.

If A/V connection is used, the TV’s VIDEO/TV Switch has

 

not been set to VIDEO.

 

 

Playback picture is blurred or

The video heads are dirty or worn out. Consult your nearest

interrupted.

JVC dealer for head cleaning or replacement.

 

 

The counter indication is blurred

This is normal.

during Still playback.

 

 

 

TAPE TRANSPORT

 

The tape stops during fast-forward or

The Counter Memory Function has been activated

rewind.

( pg. 31).

 

 

Rewinding or fast-forwarding cannot

The tape is already fully wound on one reel or the other.

be performed.

 

Image 48
Contents GR-SXM607 GR-SXM55 It is recommended that you Connection to the mains supply in the United KingdomSome DO’S and DON’TS on the Safe USE of Equipment Automatic Demonstration Audio/Video CableHow To Attach The Core Filter Power Charging the Battery PackTo Detach The Battery Pack Slide Battery Release and pull out the battery packUsing the Battery Pack Using AC PowerPerform of Charging the Battery Pack  pg Approximate recording time unit minGrip Adjustment Viewfinder AdjustmentShoulder Strap Attachment Tripod MountingPower lamp Menu Wheel Power Switch DisplayRecording Format Setting 10ENEN11 Regular VHS VCRRecording Mode Setting Tape Length SettingSet the tape recording mode depending on your preference 12ENLoading/Unloading a Cassette EN13Open the LCD monitor fully 14EN Shooting While Watching LCD MonitorTo Stop Recording Rotate Bright until the bright levelEN15 Journalistic ShootingSELF-RECORDING 16EN ZoomZoom Out EN17 18EN SnapshotNight-Scope If you press during Record-StandbyFade/Wipe Effects EN19Fades in/out to a black screen Captures faster action than Sports mode 20ENProgram AE With Special Effects High shutter speed clearly captures fast-moving actionDigital Effects EN21Using Menus For Detailed Adjustment 22ENIf you select Jlip ID no EN23 Menu Screen ExplanationsCamera Menu System Menu24EN Date/Time Insert Instant TitlesEN25 Time-Lapse Set REC Time  and 2 of Animation aboveExposure Control EN27Focusing 28ENAuto Focus Manual FocusWhite Balance Adjustment Manual White Balance OperationEN29 Press Menu again to close the Menu ScreenLoad a tape  pg Set the Power Switch to 30ENTo cancel the effect, select OFF in step EN31Use the provided Cable Adapter CamcorderPower supply instead of the battery pack  pg Basic ConnectionsTape Dubbing EN3334EN Cassette Adapter optionalUsing the Remote Control Unit GR-SXM607 only EN35 Functions Buttons36EN Using the Remote Control Unit GR-SXM607 only Playback Zoom Animation and Time-LapseEN37 38EN Using the Remote Control Unit GR-SXM607 only Insert EditingAudio Dubbing EN39For Insert Editing and Audio Dubbing SET REMOTE/VCR Code VCR Recording deckYou are now ready to try Random Assemble Editing Connect the editing cable to the R.A.EDIT connector EN41Make Connections Connect the editing cable to the Remote Pause terminal42EN Using the Remote Control Unit GR-SXM607 only Select ScenesEN43 Automatic Editing to VCRWhen the Power Switch is set to or and the LCD monitor is Viewfinder switches off automatically to save power44EN As necessary before you start shootingTo prevent damage and prolong service life EN45Use only the following batteries To avoid hazard46EN EN47 48EN EN49 50EN # $ % 3 4 5 y u 8 9EN51 52EN Indications During RecordingIndications During Playback EN5354EN Pg , 6Digital Zoom EN55