JVC 1000MKV*UN*VP, LYT0672-001A specifications EN47

Page 47

LCD Monitor

1.To prevent damage to the LCD monitor, DO NOT . . .

... push it strongly or apply any shocks.

... place the camcorder with the LCD monitor on the bottom.

2.To prolong service life . . .

... avoid rubbing it with coarse cloth.

3.Be aware of the following phenomena for LCD monitor use. These are not malfunctions:

While using the camcorder, the surface around the LCD monitor and/or the back of the LCD monitor may heat up.

If you leave power on for a long time, the surface around the LCD monitor becomes hot.

About moisture condensation . . .

You may have observed that pouring a cold liquid into a glass will cause drops of water to form on the glass’ outer surface. This same phenomenon occurs on the head drum of a camcorder when it is moved from a cool place to a warm place, after heating a cold room, under extremely humid conditions or in a place directly subjected to the cool air from an air conditioner.

Moisture on the head drum can cause severe damage to the video tape, and can lead to internal damage to the camcorder itself.

Serious malfunctioning

If malfunctioning occurs, stop using the unit immediately and consult your local JVC dealer.

EN47

For Your Maintenance

1. After Use

1Set the Power Switch to “OFF” to turn off the camcorder.

2Open the LCD monitor to an angle of over 60 degrees. Slide EJECT to open the cassette holder, then remove the cassette.

3Close and lock the cassette holder by pressing the Close button.

4Close and lock the LCD monitor.

5Slide BATTERY RELEASE to remove the battery pack.

6Attach the provided lens cap to the camcorder’s lens.

2.Cleaning The Camcorder

1 CLEAN EXTERIOR

Wipe gently with a soft cloth.

Put cloth in diluted mild soap and wring it well to wipe off heavy dirt, then wipe again with a dry cloth.

2 CLEAN LCD MONITOR

Open the LCD monitor and wipe it gently with a soft cloth. Be careful not to damage the monitor. Close the LCD monitor.

3 CLEAN LENS

Blow it with a blower brush, then wipe it gently with lens cleaning paper.

4 REMOVE EYEPIECE

Turn the eyepiece counterclockwise and pull it out.

5 CLEAN VIEWFINDER

Remove dust using a blower brush.

6RE-ATTACH EYEPIECE

Re-attach the eyepiece and turn it clockwise.

NOTES:

Avoid using strong cleaning agents such as benzine or alcohol.

Cleaning should be done only after the battery pack has been removed or other power units have been disconnected.

Mould may form if the lens is left dirty.

When using a cleaner or chemically treated cloth, refer to the cautions that came with it.

When removing the eyepiece, be sure to hold the viewfinder securely.

Image 47
Contents GR-SXM607 GR-SXM55 Connection to the mains supply in the United Kingdom It is recommended that youSome DO’S and DON’TS on the Safe USE of Equipment Audio/Video Cable Automatic DemonstrationHow To Attach The Core Filter Slide Battery Release and pull out the battery pack PowerCharging the Battery Pack To Detach The Battery PackApproximate recording time unit min Using the Battery PackUsing AC Power Perform of Charging the Battery Pack  pgTripod Mounting Grip AdjustmentViewfinder Adjustment Shoulder Strap AttachmentMenu Wheel Power Switch Display Power lamp10EN Recording Format SettingRegular VHS VCR EN1112EN Recording Mode SettingTape Length Setting Set the tape recording mode depending on your preferenceOpen the LCD monitor fully Loading/Unloading a CassetteEN13 Rotate Bright until the bright level 14ENShooting While Watching LCD Monitor To Stop RecordingSELF-RECORDING EN15Journalistic Shooting Zoom Out 16ENZoom EN17 If you press during Record-Standby 18ENSnapshot Night-ScopeFades in/out to a black screen Fade/Wipe EffectsEN19 High shutter speed clearly captures fast-moving action Captures faster action than Sports mode20EN Program AE With Special EffectsEN21 Digital EffectsIf you select Jlip ID no Using Menus For Detailed Adjustment22EN System Menu EN23Menu Screen Explanations Camera Menu24EN EN25 Date/Time InsertInstant Titles Set REC Time  and 2 of Animation above Time-LapseEN27 Exposure ControlManual Focus Focusing28EN Auto FocusPress Menu again to close the Menu Screen White Balance AdjustmentManual White Balance Operation EN2930EN Load a tape  pg Set the Power Switch toEN31 To cancel the effect, select OFF in stepCamcorder Use the provided Cable AdapterEN33 Power supply instead of the battery pack  pgBasic Connections Tape DubbingCassette Adapter optional 34ENFunctions Buttons Using the Remote Control Unit GR-SXM607 only EN3536EN Using the Remote Control Unit GR-SXM607 only EN37 Playback ZoomAnimation and Time-Lapse Insert Editing 38EN Using the Remote Control Unit GR-SXM607 onlyFor Insert Editing and Audio Dubbing Audio DubbingEN39 You are now ready to try Random Assemble Editing SET REMOTE/VCR CodeVCR Recording deck Connect the editing cable to the Remote Pause terminal Connect the editing cable to the R.A.EDIT connectorEN41 Make ConnectionsSelect Scenes 42EN Using the Remote Control Unit GR-SXM607 onlyAutomatic Editing to VCR EN43As necessary before you start shooting When the Power Switch is set to or and the LCD monitor isViewfinder switches off automatically to save power 44ENTo avoid hazard To prevent damage and prolong service lifeEN45 Use only the following batteries46EN EN47 48EN EN49 # $ % 3 4 5 y u 8 9 50ENEN51 Indications During Recording 52ENEN53 Indications During PlaybackDigital Zoom 54ENPg , 6 EN55