Panasonic AK-HC1800N GEN-LOCK GEN-LOCK Input BNC, Dsub, PHASE-COARSE -060 to +060

Page 49

Setting of menu items

2SETTING menu

[3]GEN-LOCK

GEN-LOCK INPUT [BNC, DSUB]

For selecting whether the sync signals are to be input from the BNC or D-SUB connector.

H PHASE-COARSE [–060 to +060]

For roughly adjusting the horizontal phase.

H PHASE-FINE [–045 to +045]

For finely adjusting the horizontal phase.

SD-HD PHASE CRS [–4 to +4]

For roughly adjusting the phase of the HD video signals when SD sync signals have been input.

SD-HD PHASE FINE [–99 to +99]

For finely adjusting the phase of the HD video signals when SD sync signals have been input.

- 49 -

Image 49

Contents Multi Purpose Camera Operating InstructionsDo not Open FCC NoteIndicates safety information Important Safety Instructions Accessories ContentsBit A/D conversion and brand-new DSP featured CharacteristicsIntroduction New 2/3˝ 2.2 million-pixel CCD is employed H DON’TS Precautions for useBottom view Rear view Front view Lens mount  HD SDI output connector HD SDI OUT AK-HC1800N Interface cable specifications Tally output connector Tally OUT How to set the lens How to installConfiguration example 1 Connection of camera controller How to set up the systemConfiguration example 2 High-speed P/T system Configuration example 3 High-speed P/T system AW-PH650 BAR Control exercised from the AW-CB400When the LCD panel is in the pedestal adjustment mode Procedure for camera menu operation AW-RP655Mode How to set up the system Adjust the white balance Operation procedureAdjust the black balance Start shootingFlange back adjustment for zoom lens How to adjustLens iris gain volume adjustment Auto iris power zoom lensColor temperature and white balance adjustment reference White balance adjustmentGen-lock adjustment Black balance adjustmentIntelligent functions Automatic color temperature adjustment method Automatic video level adjustment methodHow to display the menus Setting of menu items Using AK-HRP150G camera controller TOP menuBlack Shading Detection  Maintenance menuCorrectdig OFF, on Pedestal -200 to +200 PEDESTAL, GammaPedestal -100 to +100 GammaBlack Gamma OFF, on Gamma OFF, onDRS OFF, on Cine Gamma Select Video REC, Film RECFlare 000 to FlareFlare OFF, on Manual Knee Point KNEE, White Clip When the Knee is set toKnee Point -25.00% to +25.00% Knee SlopeKnee Level 100% to 109% Knee OFF, MANUAL, Auto KNEE, White ClipWhite Clip OFF, on High Color OFF, onKnee Aperture OFF, on Detail Detail OFF, onDetail Source Detail Slim Detail OFF, onSkin GET OFF, on Skin Tone Detail Skin Tone DTL OFF, onGAIN, Auto Iris Iris Mode LENS, CAMIris Level 000 to Iris PEAK/AVE 000 toSuper Gain Mode S.GAIN1, S.GAIN2, S.GAIN3PED Offset -200 to +200 35 to 0.75 DRS OFF -10 to +10 DRS onMatrix Table A, B Frame Mode MatrixColor Correction SAT/PHASE -63 to +63Lighting TUNGSTEN, Daylight Setting menuGain Select LOW, MID, HIGH, S.GAIN1 toColor Correction OFF, on Matrix Table OFF, A, BDigital Extender OFF BAR SELStatus OFF, on FormatAWB Active AWB OKOUT Range RGB ABB OKMenu on BAR OFF, on Menu SEL Video MENU, Film MenuShutter Speed Shutter Shutter Mode OFF, ON, SynchroPHASE-FINE -045 to +045 PHASE-COARSE -060 to +060SD-HD Phase CRS -4 to +4 SD-HD Phase Fine -99 to +99Protocol 1 to ProtocolGain -6dB to 72dB INTELLIGENT1ND-FIL CLEAR, 1/4, 1/16, 1/64 Intelligent MANUAL, AUTO, LockATW AGCND Filter Select INTELLIGENT1 Intelligent Mode AGC, ATW, AGC+ATWCLEAR, 1/4, 1/16, 1/64, Auto AGC Speed 1 toHI Light Detect 01 to INTELLIGENT1 AGC Gain Step NORMAL, MAXATW Area 25%, 50%, 90% Iris Range 1, 2ATW Speed 1 to NORMAL, SPORTS, SN, User The AGC control mode is set here AGC ModeFrame MIX MIX +00dB, +06dBINTELLIGENT1 SUB Menu INTELLIGENT2 INTELLIGENT2 Intelligent SETIris on Lock LOCK, MANUAL, Panel ATW Width 1 toCamera ID menu File Operation menu Mode LOAD/STORELOAD/STORE from ExecuteMenu list Setting of menu items Maintenance Color SAT/PHASE Correction Setting of menu items Unit inch mm AppearanceInput/output signal SpecificationsEastern Zone