Panasonic AK-HC1800N operating instructions Camera ID menu

Page 62

Setting of menu items

3CAMERA ID menu

An ID of not more than 10 characters consisting of alphanumerics, symbols and spaces can be set for the camera.

The camera ID is displayed at all times when ON is selected in the CAM ID mode but displayed only when color bar signals are output in the BAR mode.

The status for setting the ID is established by moving the cursor above the colon (:) and selecting it.

Move the cursor to the positions of the characters to be set, select the characters and enter them.

Characters which can be entered: Spaces, upper-case letters (A to Z), numbers (0 to 9), and symbols (' , >, <, /, -)

- 62 -

Image 62

Contents Operating Instructions Multi Purpose CameraFCC Note Do not OpenIndicates safety information Important Safety Instructions Contents AccessoriesIntroduction CharacteristicsBit A/D conversion and brand-new DSP featured New 2/3˝ 2.2 million-pixel CCD is employed H Precautions for use DON’TSFront view Bottom view Rear view Lens mount  HD SDI output connector HD SDI OUT Interface cable specifications AK-HC1800N Tally output connector Tally OUT How to install How to set the lensHow to set up the system Configuration example 1 Connection of camera controllerConfiguration example 2 High-speed P/T system Configuration example 3 High-speed P/T system AW-PH650 Control exercised from the AW-CB400 BARProcedure for camera menu operation AW-RP655 When the LCD panel is in the pedestal adjustment modeMode How to set up the system Adjust the black balance Operation procedureAdjust the white balance Start shootingLens iris gain volume adjustment How to adjustFlange back adjustment for zoom lens Auto iris power zoom lensWhite balance adjustment Color temperature and white balance adjustment referenceBlack balance adjustment Gen-lock adjustmentIntelligent functions Automatic video level adjustment method Automatic color temperature adjustment method Using AK-HRP150G camera controller Setting of menu itemsHow to display the menus TOP menuCorrectdig OFF, on  Maintenance menuBlack Shading Detection Pedestal -100 to +100 PEDESTAL, GammaPedestal -200 to +200 GammaDRS OFF, on Gamma OFF, onBlack Gamma OFF, on Cine Gamma Select Video REC, Film RECFlare OFF, on FlareFlare 000 to Knee Point -25.00% to +25.00% KNEE, White Clip When the Knee is set toManual Knee Point Knee SlopeKnee Level 100% to 109% White Clip OFF, on KNEE, White ClipKnee OFF, MANUAL, Auto High Color OFF, onDetail Detail OFF, on Knee Aperture OFF, onDetail Slim Detail OFF, on Detail SourceSkin Tone Detail Skin Tone DTL OFF, on Skin GET OFF, onIris Level 000 to Iris Mode LENS, CAMGAIN, Auto Iris Iris PEAK/AVE 000 toMode S.GAIN1, S.GAIN2, S.GAIN3 Super Gain35 to 0.75 DRS OFF -10 to +10 DRS on PED Offset -200 to +200Frame Mode Matrix Matrix Table A, BSAT/PHASE -63 to +63 Color CorrectionGain Select Setting menuLighting TUNGSTEN, Daylight LOW, MID, HIGH, S.GAIN1 toDigital Extender OFF Matrix Table OFF, A, BColor Correction OFF, on BAR SELAWB Active FormatStatus OFF, on AWB OKMenu on BAR OFF, on ABB OKOUT Range RGB Menu SEL Video MENU, Film MenuShutter Shutter Mode OFF, ON, Synchro Shutter SpeedSD-HD Phase CRS -4 to +4 PHASE-COARSE -060 to +060PHASE-FINE -045 to +045 SD-HD Phase Fine -99 to +99Protocol Protocol 1 toND-FIL CLEAR, 1/4, 1/16, 1/64 INTELLIGENT1Gain -6dB to 72dB Intelligent MANUAL, AUTO, LockAGC ATWCLEAR, 1/4, 1/16, 1/64, Auto INTELLIGENT1 Intelligent Mode AGC, ATW, AGC+ATWND Filter Select AGC Speed 1 toINTELLIGENT1 AGC Gain Step NORMAL, MAX HI Light Detect 01 toATW Speed 1 to Iris Range 1, 2ATW Area 25%, 50%, 90% AGC Mode NORMAL, SPORTS, SN, User The AGC control mode is set hereMIX +00dB, +06dB Frame MIXINTELLIGENT1 SUB Menu INTELLIGENT2 Intelligent SET INTELLIGENT2ATW Width 1 to Iris on Lock LOCK, MANUAL, PanelCamera ID menu LOAD/STORE from Mode LOAD/STOREFile Operation menu ExecuteMenu list Setting of menu items Maintenance Color SAT/PHASE Correction Setting of menu items Appearance Unit inch mmSpecifications Input/output signalEastern Zone