Bosch Appliances NDC-265-P operation manual Installation, Disassembly

Page 15

IP Camera 200 Series	Installation en 15

3Installation

3.1Disassembly

The camera/housing unit consists of the following parts:

x2

1.Dome

2.Inner liner

3.Camera module and mounting base

To disassemble the unit proceed as follows:

1.Using the special screwdriver bit supplied, loosen the two tamper-resistant screws in the dome (the screws remain in place).

2.Remove the dome from the base.

3.Remove the inner liner by pulling it off the base.

Bosch Security Systems

Installation and Operation Manual

AR18-10-B012 v1.5 2011.01

Image 15

Contents IP Camera 200 Series Page Table of Contents Advanced Mode Basic ModeOperation via the browser Troubleshooting 101 Maintenance 103Technical Data 105 Safety precautions SafetyImportant safety instructions FCC & Ices Information FCC & Ices complianceMore information UL certificationBosch notices DisclaimerCopyrights En Safety IP Camera 200 Series Introduction FeaturesCD ROM UnpackingDisassembly InstallationMicroSDHC card MicroSDHC cardRJ45 Ethernet PoE Network and power connectorDC power connection Power connectionFunction Pin Socket I/O connectorAudio connectors Audio connectorsMounting the camera MountingCamera positioning Camera set-upIP Camera 200 Series Installation en Focal length and focus Closing the unit Resetting the cameraEn Installation IP Camera 200 Series Browser connection System requirementsEstablishing the connection Protected network Password protection in cameraLivepage Connection establishedEn Browser connection IP Camera 200 Series Basic Mode Basic Mode menu treeSaving changes Camera name Device AccessPassword PasswordConfirm password Date/TimeDevice date, time and zone Subnet mask Click Set and RebootNetwork IP addressSystem Overview EncoderAudio RecordingEn Basic Mode IP Camera 200 Series Advanced Mode menu tree Advanced ModeCamera name GeneralIdentification Camera IDPassword Device time zone Date/TimeDate format Device date / Device timeCamera name stamping Display StampingTime server IP address Time server typeDisplay milliseconds Alarm mode stampingAlarm message Time stampingCompany logo Web InterfaceAppearance Website languageLivepage Functions Logging Camera Picture SettingsDefault AR18-10-B012 v1.5 Maximum bit rate Profile ConfigurationProfile name Target bit rate720p Video resolutionExpert Settings 4CIF/D1Default Encoder Streams Audio Flip image Installer MenuCamera LED Mirror imageRecording ISCSI Media Storage ManagementDevice manager Recording mediaActivating and Configuring Storage Media Deactivating Storage Media Formatting Storage MediaStandard recording Stream profile settingsRecording Profiles Recording includesAlarm recording Retention Time Recording Scheduler WeekdaysHolidays Recording status Recording StatusProfile names Activate recordingAlarm Connections AlarmRemote port Select 10 in the Number of destination IP address list boxVideo transmission StreamAudio DecoderSSL encryption Auto-connectVideo Content Analyses VCA Aggregation time s VCA configuration- ProfilesAnalysis type Motion detectorSensitivity Tamper detection Minimum object sizeDebounce time 1 s Selecting the areaScene too bright Trigger delay sGlobal change slider Global changeScene too dark Scene too noisyReference check Appearing edges Deleting Holidays VCA configuration ScheduledIP Camera 200 Series Advanced Mode en Trigger active VCA configuration Event triggeredDelay s TriggerName Audio AlarmAudio alarm Signal RangesAlarm E-Mail Destination address Sender nameTest e-mail Alarm input InterfacesRelay Relay follows Relay nameTrigger relay Automatic IP assignment Network AccessHttps browser port DNS server addressDetails Video transmission Http browser portTelnet support Interface mode ETHEnable DynDNS RCP+ portStatus Host nameUser name Force registration nowSnmp traps AuthenticationAdvanced Snmp host address / 2. Snmp host addressTCP metadata input MulticastRtsp port UPnPStreaming EnableMulticast Address PortFTP Posting Service MaintenanceFirmware SSL certificate ConfigurationSystem Overview Maintenance logOperation via the browser LivepageProcessor load Image selection System Log / Event Log Digital I/OAudio communication Saving snapshotsRecording video sequences Running recording programIP Camera 200 Series Operation via the browser en Export to FTP RecordingsControlling playback Selecting RecordingsBookmarks Slide controlEn Operation via the browser IP Camera 200 Series Customer service TroubleshootingLED indicators Resolving problemsEn Troubleshooting IP Camera 200 Series Maintenance RepairsTransfer and disposal En Maintenance IP Camera 200 Series Specifications Technical DataAccessories Page Bosch Security Systems