Bosch Appliances NDC-265-P Encoder, Audio, Recording, System Overview, Storage medium

Page 35

IP Camera 200 Series	Basic Mode en 35

5.5Encoder

Select a profile for encoding the video signal. Pre-programmed profiles are available that give priority to different parameters. When a profile is selected, its details are displayed.

Main frequency and Operation environment

Select 50 Hz or 60 Hz as the main frequency, and Indoor or Outdoor for the operation environment.

5.6Audio

Switch the camera microphone On or Off.

5.7Recording

Record the images from the camera to a storage medium. For long-term authoritative images, it is essential to use an NVR or an appropriately sized iSCSI system.

5.7.1Storage medium

1.Select the required storage medium from the list.

2.Click Start to start recording or Stop to end recording.

5.8System Overview

This page provides general information on the hardware and firmware system, including version numbers. No items can be changed on this page but they can be copied for information purposes when troubleshooting.

Bosch Security Systems

Installation and Operation Manual

AR18-10-B012 v1.5 2011.01

Image 35

Contents IP Camera 200 Series Page Table of Contents Advanced Mode Basic ModeOperation via the browser Technical Data 105 Troubleshooting 101Maintenance 103 Safety precautions SafetyImportant safety instructions FCC & Ices Information FCC & Ices complianceMore information UL certificationBosch notices DisclaimerCopyrights En Safety IP Camera 200 Series Introduction FeaturesCD ROM UnpackingDisassembly InstallationMicroSDHC card MicroSDHC cardRJ45 Ethernet PoE Network and power connectorDC power connection Power connectionFunction Pin Socket I/O connectorAudio connectors Audio connectorsMounting the camera MountingCamera positioning Camera set-upIP Camera 200 Series Installation en Focal length and focus Closing the unit Resetting the cameraEn Installation IP Camera 200 Series Establishing the connection Browser connectionSystem requirements Protected network Password protection in cameraLivepage Connection establishedEn Browser connection IP Camera 200 Series Saving changes Basic ModeBasic Mode menu tree Camera name Device AccessPassword PasswordDevice date, time and zone Confirm passwordDate/Time Subnet mask Click Set and RebootNetwork IP addressSystem Overview EncoderAudio RecordingEn Basic Mode IP Camera 200 Series Advanced Mode menu tree Advanced ModeCamera name GeneralIdentification Camera IDPassword Device time zone Date/TimeDate format Device date / Device timeCamera name stamping Display StampingTime server IP address Time server typeDisplay milliseconds Alarm mode stampingAlarm message Time stampingCompany logo Web InterfaceAppearance Website languageLivepage Functions Logging Camera Picture SettingsDefault AR18-10-B012 v1.5 Maximum bit rate Profile ConfigurationProfile name Target bit rate720p Video resolutionExpert Settings 4CIF/D1Default Encoder Streams Audio Flip image Installer MenuCamera LED Mirror imageRecording ISCSI Media Storage ManagementDevice manager Recording mediaActivating and Configuring Storage Media Deactivating Storage Media Formatting Storage MediaStandard recording Stream profile settingsRecording Profiles Recording includesAlarm recording Retention Time Holidays Recording SchedulerWeekdays Recording status Recording StatusProfile names Activate recordingAlarm Connections AlarmRemote port Select 10 in the Number of destination IP address list boxVideo transmission StreamAudio DecoderSSL encryption Auto-connectVideo Content Analyses VCA Aggregation time s VCA configuration- ProfilesSensitivity Analysis typeMotion detector Tamper detection Minimum object sizeDebounce time 1 s Selecting the areaScene too bright Trigger delay sGlobal change slider Global changeReference check Scene too darkScene too noisy Appearing edges Deleting Holidays VCA configuration ScheduledIP Camera 200 Series Advanced Mode en Trigger active VCA configuration Event triggeredDelay s TriggerName Audio AlarmAudio alarm Signal RangesAlarm E-Mail Test e-mail Destination addressSender name Relay Alarm inputInterfaces Trigger relay Relay followsRelay name Automatic IP assignment Network AccessHttps browser port DNS server addressDetails Video transmission Http browser portTelnet support Interface mode ETHEnable DynDNS RCP+ portStatus Host nameUser name Force registration nowSnmp traps AuthenticationAdvanced Snmp host address / 2. Snmp host addressTCP metadata input MulticastRtsp port UPnPStreaming EnableMulticast Address PortFTP Posting Firmware ServiceMaintenance SSL certificate ConfigurationSystem Overview Maintenance logProcessor load Operation via the browserLivepage Image selection System Log / Event Log Digital I/OAudio communication Saving snapshotsRecording video sequences Running recording programIP Camera 200 Series Operation via the browser en Export to FTP RecordingsControlling playback Selecting RecordingsBookmarks Slide controlEn Operation via the browser IP Camera 200 Series Customer service TroubleshootingLED indicators Resolving problemsEn Troubleshooting IP Camera 200 Series Transfer and disposal MaintenanceRepairs En Maintenance IP Camera 200 Series Specifications Technical DataAccessories Page Bosch Security Systems