Axis Communications P5534 user manual Storage, UPnPTM, RTP/H.264, Bonjour, SD card

Page 43

AXIS P5534 PTZ Dome Network Camera

System Options

The following traps are available:

Cold start

Warm start

Link up

Authentication failed

SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required.

To use SNMP v3, HTTPS must be enabled, see HTTPS, on page 37. To enable SNMP v3, check the box and provide the initial user password.

Note

The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see Reset to factory default settings, on page 46.

UPnPTM

The Axis product includes support for UPnPTM. UPnPTM is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

UPnPTM can be disabled under System Options > Network > UPnPTM.

RTP/H.264

The RTP port range and multicast settings are configured under System Options > Network > RTP.

The RTP port range defines the range of ports from which the video/audio ports are automatically selected. For multicast streams, only certain IP addresses and port numbers should be used.

Select Always Multicast Video and/or Always Multicast Audio to start multicast streaming without opening an RTSP session.

Bonjour

The Axis product includes support for Bonjour. Bonjour is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

Bonjour can be disabled under System Options > Network > Bonjour.

Storage

SD card

The SD/SDHC memory card (not included) is managed on the System Options > Storage page. Click SD card to open Storage Management.

Mounting is done automatically when the card is inserted or when the product boots. SD cards are normally preformatted when purchased, but if needed, click Format to format the card.

Format an SD card so that it can be written to one of two available options — VFAT and ext4. During the formatting any previous data stored on the disk will be lost. The recommended format is ext4, due to its resilience against data loss if the card is ejected or if there is abrupt power loss. A third-party ext4 driver or application is also needed to access the file system from Windows.

Note that most SD cards are pre-formatted with vFAT when purchased. The Check Disk option is used to check for errors on the SD card and only works for the file system ext4. The Repair option repairs the SD card of errors in the file system ext4. For vFAT file system use a card reader or PC to perform card maintenance.

Note

To prevent corruption of recordings, the SD card should always be unmounted before removal.

43

Image 43
Contents Axis P5534 PTZ Dome Network Camera Equipment Modifications About this documentLiability Intellectual Property RightsAxis P5534 PTZ Dome Network Camera Table of ContentsPerformance considerations Symptoms, possible causes and remedial actionsHardware overview ConnectorsHardware overview Midspan LED indicators LED indicatorsColor Indication Start a browser Internet Explorer, Firefox, Safari Accessing the productAccessing the product Access from a browserNetwork TCP/IP Advanced Access from the InternetSet the root password Live ViewAxis Media Control viewer toolbar Controls on the Live ViewAMC Audio controls PTZ ControlsAxis P5534 PTZ Dome Network Camera Axis Media Control AMC How to stream H.264Media streams Media streamsQuickTimeTM. The following paths can be used Alternative methods of accessing the video streamJava applet supports simplex audio with G.711 encoding Accessing audio streamsSetting up the product Setting up the productBasic Setup Pixel Counter Video and AudioVideo and Audio Video Stream264 Camera SettingsStream Profiles ImageWhite balance Exposure SettingsImage settings Image AppearanceOverlay image Audio SettingsOverlay Privacy MaskG711 G726 Audio InputAudio Output Audio ClipsLive View Config Default viewer for browsersLive View Config Browser Viewer Description Viewer SettingsUser Defined Links Output ButtonsAxis P5534 PTZ Dome Network Camera Gatekeeper Preset PositionsPTZ Pan Tilt Zoom PTZ Pan Tilt ZoomLimits Guard TourOsdi Zones AdvancedControl Queue Operator Same as administrator but with lower priorityControls Motion Detection Set up motion detectionDetectors DetectorsAudio detection Applications ApplicationsEvents EventsGo to Events Action Rules and click Add Setting Up an Action RuleConvert Event Types to Action Rules PTZ ControlGo to Events Recipients and click Add RecipientsSchedules Recipient Use with actionGo to Events Recurrences and click Add RecurrencesContinuous recording RecordingsRecordings Recording ListAxis P5534 PTZ Dome Network Camera Users System OptionsSystem Options SecurityIeee Date & TimeAudio Support IPv6 Address Configuration Basic TCP/IP SettingsNetwork IPv4 Address ConfigurationAdvanced TCP/IP Settings NAT traversal port mapping for IPv4 Link-Local IPv4 AddressSmtp email QoS Quality of ServiceBonjour StorageUPnPTM RTP/H.264Ports MaintenancePorts & Devices Network ShareLogs & Reports SupportSupport Overview System OverviewPlain Config Reset to factory default settingsScripting File UploadMulti-Connector Cable sold separately Multi-Connector Cable sold separatelyFunction Pin Specifications Connector DC power input Connection diagramChecking the firmware TroubleshootingTroubleshooting Emergency recovery procedureProblems setting the IP address Symptoms, possible causes and remedial actionsProduct cannot be accessed from a browser Problems with the H.264 format Product is accessible locally but not externallyNo images displayed on web Video and image problems, generalSetup Video & Audio Camera Settings Problems uploading filesPoor audio quality SettingsStorage and disk management problems No audioTechnical Specifications Technical SpecificationsFunction/group Specifications Network Security Maintenance Installation aidsMemory Power ConnectorsPerformance considerations Ver M1.12 Axis P5534 PTZ Dome Network Camera