Axis Communications P5534E user manual Storage, RTP/H.264, Bonjour, Mount and Unmount SD Card

Page 43

AXIS P5534–E PTZ Dome Network Camera

System Options

RTP/H.264

The RTP port range and multicast settings are configured under System Options > Network > RTP.

The RTP port range defines the range of ports from which the video ports are automatically selected. For multicast streams, only certain IP addresses and port numbers should be used.

Select Always Multicast Video to start multicast streaming without opening an RTSP session.

Bonjour

The Axis product includes support for Bonjour. Bonjour is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

Bonjour can be disabled under System Options > Network > Bonjour.

Storage

SD Card

NOTICE

To prevent data corruption, the SD card should always be unmounted before it is ejected.

Note

For SD card recommendations see www.axis.com

The Axis product supports SD cards with up to 64 GB of storage. For best recording performance, use an SDHC or SDXC card with speed class 10.

The following SD card file systems are supported:

•ext4 — recommended due to its resilience against data loss if the card is ejected or if there is abrupt power loss. To access data stored on the card from the Windows operating system, a third-party ext4 driver or application is required.

•vFAT — supported by most operating systems for personal computers.

The SD card is managed on the System Options > Storage page. Click SD Card to open Storage Management.

If the card’s status shows as failed, click Check disk to see if the problem can be found and then try Repair. This option is only available for SD cards with ext4. For SD cards with vFAT, use a card reader or computer to troubleshoot the card.

To avoid filling the card, it is recommended to remove recordings continuously. Under General Settings, select Remove recordings older than and select the number of days or weeks.

To stop writing to the card and protect recordings from being removed, select Lock under General Settings.

Mount and Unmount SD Card

NOTICE

To prevent corruption of recordings, the SD card should always be unmounted before it is ejected.

The SD card is automatically mounted when the card is inserted into the Axis product or when the product is started. A manual mount is only required if the card has been unmounted and not ejected and re-inserted.

To unmount the SD card:

1.Open the Axis product’s webpages and go to Setup > System Options > Storage.

2.Click SD Card.

43

Page 42 Page 44
Image 43
Page 42 Page 44
Contents Axis P5534-E PTZ Dome Network Camera Intellectual Property Rights About this documentLegal Considerations LiabilityLearn More SupportAxis P5534-E PTZ Dome Network Camera Table of ContentsHardware Overview Connectors and ButtonsNetwork Connector For technical specifications, seeControl Button LED IndicatorsMidspan LED Indicators SD Card SlotAccess from a Browser Access the ProductAccess from the Internet Live View Set the Root PasswordClick Create self-signed certificate Manual Trigger Go to Setup EventsControls on the Live View Axis Media Control viewer toolbarPTZ Controls Axis P5534-E PTZ Dome Network Camera Media Streams How to Stream H.264Axis Media Control AMC QuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamAxis P5534-E PTZ Dome Network Camera Basic Setup Set Up the ProductPixel Counter Set Up Video StreamsClick Save to apply the new settings Video264 Stream ProfilesWhite Balance Camera SettingsExposure Settings Image AppearanceOverlay Image Image SettingsDate/Time Formats in the online help To enable overlays OverlayTo upload an overlay image Privacy MaskGo to Video Overlay Image Browser Viewer Description Configure the Live ViewDefault Viewer for Browsers Viewer SettingsUser Defined Links Go to Setup Live View ConfigOutput Buttons PTZ Pan Tilt Zoom Preset PositionsGatekeeper Limits Guard TourOsdi Zones AdvancedControls Control Queue Operator Same as administrator but with lower priorityMotion Detection Parameters Set Up Motion Detection WindowsDetectors Motion DetectionLow level 0% Default valuesHigh level 100% Medium level 50%Application Licenses Install ApplicationGo to Setup Applications ApplicationsAxis P5534-E PTZ Dome Network Camera Go to Events Action Rules and click Add Set Up Action RulesEvents Convert Event Types to Action RulesActions TriggersCreate Schedules Add RecipientsRecipient Types Go to Events Recurrences and click Add Set Up RecurrencesGo to Recordings List RecordingsRecording List Continuous RecordingUsers To log in again and be configured to use this functionalitySystem Options SecurityCA Certificate Date & TimeIeee CertificatesNetwork Basic TCP/IP SettingsLinux/Unix example Axis Internet Dynamic DNS ServiceAxis Internet Dynamic DNS Service requires IPv4 Linux/Unix syntaxHost Name Configuration Advanced TCP/IP SettingsDNS Configuration NTP ConfigurationFTP NAT traversal port mapping for IPv4UPnPTM QoS Quality of ServiceUPnPTM can be disabled under System Options Network UPnPTM Smtp emailSD Card StorageRTP/H.264 BonjourGo to System Options Storage Click Network Share MaintenanceNetwork Share Format SD CardLogs & Reports SupportSupport Overview System OverviewFile Upload Reset to Factory Default SettingsPlain Config ScriptingAxis P5534-E PTZ Dome Network Camera Check the Firmware TroubleshootingUpgrade the Firmware Emergency Recovery ProcedureProduct is accessible locally but not externally Symptoms, Possible Causes and Remedial ActionsProblems setting the IP address Product cannot be accessed from a browserKey frames Problems with streaming H.264Video and image problems, general Video Camera SettingsCondensation in dome Storage and disk management problemsTechnical Specifications Connectors Function/group Specifications System ApplicationMaintenance Installation aids Memory PowerPerformance Considerations Function/group Specifications VideoM2.4
Top Page Image Contents