Axis Communications M3024LVE user manual QoS Quality of Service, Smtp email, UPnPTM

Page 43

AXIS M3024–LVE Network Camera

System Options

QoS (Quality of Service)

QoS (Quality of Service) guarantees a certain level of a specified resource to selected traffic on a network. A QoS-aware network prioritizes network traffic and provides a greater network reliability by controlling the amount of bandwidth an application may use.

The QoS settings are configured under System Options > Network > QoS. Using DSCP (Differentiated Services Codepoint) values, the Axis product can mark the following types of traffic: live video, event/alarm traffic and management traffic.

SMTP (email)

To send email messages from the Axis product via SMTP (Simple Mail Transfer Protocol), an SMTP mail server must be set up. This is done under System Options > Network > SMTP (email).

Enter the host names or IP addresses and port numbers for the primary and secondary mail servers in the fields provided. A From email address is also required. If the mail server requires authentication, check Use authentication to log in to this server and enter the necessary information.

SNMP

The Simple Network Management Protocol (SNMP) allows remote management of network devices. An SNMP community is the group of devices and management station running SNMP. Community names are used to identify groups.

The Axis product can be configured to support SNMP on the System Options > Network > SNMP page.

Depending on the level of security required, select the version on SNMP to use.

SNMP v1/v2 provides the lowest level of security. The community name can be specified as a password for read or read/write access to all supported SNMP devices. The default password for the Read community is public and the default password for the Write community is write.

Note

If HTTPS is enabled, SNMP v1 and SNMP v2c should be disabled.

Traps for SNMP v1/v2 are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

The following traps are available:

•Cold start

•Warm start

•Link up

•Authentication failed

SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required.

To use SNMP v3, HTTPS must be enabled, see HTTPS, on page 37. To enable SNMP v3, check the box and provide the initial user password.

Note

The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see Reset to Factory Default Settings, on page 47.

UPnPTM

The Axis product includes support for UPnPTM. UPnPTM is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

UPnPTM can be disabled under System Options > Network > UPnPTM.

43

Page 42 Page 44
Image 43
Page 42 Page 44
Contents Axis M3024-LVE Network Camera Intellectual Property Rights About this DocumentLegal Considerations LiabilityLearn More SupportAxis M3024-LVE Network Camera Table of ContentsHardware Overview Connectors and ButtonsNetwork Connector Hardware OverviewControl Button LED IndicatorsConnector SD Card SlotAccessing the Product Accessing the ProductAccess from a Browser Set the Root Password Accessing the Product Access from the InternetClick Create self-signed certificate Live View Set Power Line FrequencyControls on the Live View Axis Media Control viewer toolbar Go to Setup EventsManual Trigger PTZ Controls Axis Media Control AMC How to Stream H.264Media Streams Media StreamsAlternative Methods of Accessing the Video Stream Axis M3024-LVE Network Camera Setting Up the Product Setting Up the ProductBasic Setup Video Stream Setting Up the Product VideoPixel Counter Image Stream Profiles264 White Balance Camera SettingsExposure Settings Image AppearanceOverlay View AreaBuilt-in IR Illuminations LEDs Overlay Image Privacy MaskGo to Video Overlay Image Live View Config Live View ConfigDefault Viewer for Browsers Output Buttons Viewer SettingsGo to Setup Live View Config User Defined LinksAxis M3024-LVE Network Camera Advanced Preset PositionsPTZ Pan Tilt Zoom PTZ Pan Tilt ZoomAxis M3024-LVE Network Camera Motion Detection DetectorsDetectors Camera TamperingParameter Object Size History Sensitivity Description Set Up Motion Detection WindowsMotion Detection Parameters Go to Detectors Motion DetectionRecommended values Default valuesMedium level 50% Low level 0%Application Licenses Install ApplicationApplications ApplicationsAxis M3024-LVE Network Camera Events EventsGo to Events Action Rules and click Add Setting Up an Action RuleTime PTZ ControlSchedules RecipientsRecurrences Go to Events Recurrences and click Add Continuous Recording RecordingsRecordings Recording ListLanguages LanguagesUsers System OptionsSystem Options SecurityIeee Date & TimeCertificates Network Basic TCP/IP SettingsAxis Video Hosting System Avhs Axis Internet Dynamic DNS ServiceLinux/Unix syntax Linux/Unix exampleHost Name Configuration Advanced TCP/IP SettingsDNS Configuration NTP ConfigurationFTP NAT traversal port mapping for IPv4UPnPTM QoS Quality of ServiceUPnPTM can be disabled under System Options Network UPnPTM Smtp emailSD Card StorageRTP/H.264 BonjourPorts MaintenancePorts & Devices Network ShareLogs & Reports SupportSupport Overview System OverviewScripting Reset to Factory Default SettingsPlain Config System Options AdvancedChecking the Firmware TroubleshootingTroubleshooting Emergency Recovery ProcedureProblems setting the IP address Symptoms, Possible Causes and Remedial ActionsProduct cannot be accessed from a browser Problems with streaming H.264 Product is accessible locally but not externallyBasic Problem Retrieving Additional Video Streams Technical Specifications Technical SpecificationsDimensions Function/group Specifications System ApplicationPower ConnectorsFunction Pin Specifications ConnectorsFunction/group Specifications Weight 820 g 12.8 lb Included ConnectorPerformance Considerations M2.4

M3024LVE specifications

Axis Communications M3024LVE is a compact, high-performance network camera designed for versatile indoor and outdoor surveillance applications. With its sleek and discreet design, this camera is an optimal choice for businesses and public spaces that require reliable security without compromising aesthetics.

One of the key features of the M3024LVE is its impressive image quality. Equipped with a 2 megapixel sensor, this camera offers a resolution of 1920 x 1080 pixels, delivering clear and detailed images. The camera supports H.264 and Motion JPEG video compression formats, which ensures smooth streaming and efficient storage without sacrificing video quality. This capability is particularly beneficial for organizations with limited storage resources, allowing them to conserve bandwidth while maintaining high-resolution video.

Another notable characteristic of the M3024LVE is its built-in infrared (IR) illumination. This feature allows the camera to capture clear images in complete darkness, enhancing its effectiveness in low-light conditions. With a range of up to 30 meters, the IR capability ensures that critical surveillance areas are monitored around the clock. This makes the M3024LVE an excellent choice for both day and night monitoring in a variety of environments.

The M3024LVE is also designed with robust weather-resistant capabilities. With an IP66 and NEMA 4X rating, it can withstand harsh weather conditions, including rain, snow, and dust. This durability makes it suitable for outdoor installations, ensuring that users can rely on its performance regardless of the environmental challenges.

In addition to its physical characteristics, the M3024LVE integrates advanced video analytics, enhancing its functionality. Features such as motion detection, audio detection, and tampering alarm enable users to receive real-time alerts based on specific events or activities, facilitating proactive monitoring.

Moreover, Axis Communications places a strong emphasis on cybersecurity, and the M3024LVE is no exception. The camera includes several security features such as secure access, HTTPS encryption, and the ability to implement user access controls. This ensures that only authorized personnel can access the camera feed, protecting sensitive surveillance data from potential threats.

Overall, the Axis Communications M3024LVE combines high image quality, robust weather resistance, and advanced analytics in a compact design, making it an ideal solution for a myriad of surveillance needs in both indoor and outdoor environments.
Top Page Image Contents