Kenwood KDC-X717 instruction manual Accessories, Installation Procedure

Page 43

Accessories

External view	External view
......... Number of items	......... Number of items

Installation Procedure

1.	To prevent a short circuit, remove the key from the ignition and
	disconnect the - battery.
2.	Make the proper input and output wire connections for each unit.
3.	Connect the speaker wires of the wiring harness.

1

2

3

4

5

6

2CAUTION

.........1	7	1
.........1
.........1	8	1
.........1	.........	1
.........2	9	1
	.........	1
.........1	0	1
.........1	.........	1
.........2
.........2

4.	Connect the wiring harness wires in the following order: ground,
	battery, ignition.
5.	Connect the wiring harness connector to the unit.
6.	Install the unit in your car.
7.	Reconnect the - battery.
8.	Press the left part at the upper side of the faceplate once to
	make the faceplate control panel appear.

2CAUTION

• If your car's ignition does not have an ACC position, connect

the ignition wires to a power source that can be turned on

and off with the ignition key. If you connect the ignition wire

to a power source with a constant voltage supply, as with

battery wires, the battery may die.

• If the console has a lid, make sure to install the unit so that

the faceplate will not hit the lid when closing and opening.

• If the fuse blows, first make sure the wires aren’t touching

to cause a short circuit, then replace the old fuse with one

with the same rating.

• Do not let unconnected wires or terminals touch metal on

the car or anything else conducting electricity. To prevent a

short circuit, do not remove the caps on the ends of the

unconnected wires or the terminals.

• Connect the speaker wires correctly to the terminals to

Do not use any accessories other than those provided with your unit. If you use other accessories, you may damage the

which they correspond. The unit may be damaged or fail to

work if you share the - wires or ground them to any metal

part in the car.

• After the unit is installed, check whether the brake lamps,

blinkers, wipers, etc. on the car are working properly.

• Insulate unconnected wires with vinyl tape or other similar

material.

• Some disc changers need conversion cords for connection.

See the section on "Safety Precautions" for details.

• Mount the unit so that the mounting angle is 30° or less.

— 43 —

Image 43

Contents KDC-X917 KDC-X817 KDC-9017 KDC-X717 Contents 2Warning To prevent injury or fire, take the following precautions Safety precautionsLens Fogging Cleaning the CD SlotCleaning the Faceplate Terminals Cleaning the UnitChecking New CDs for Burrs Cleaning CDsHandling Compact discs Storing CDsDo Not Use CDs with Sticker on the Labeled Side Do Not Load CD AccessoriesRemoving the CD Do Not Use Special Shape CDsPower General featuresPower ON/OFF Switching Modes VolumeAttenuator System Q Speaker & Woofer settingSwitching the Preset Sound Setting LoudnessStand by mode Faceplate Angle AdjustmentSwitching Full-Screen Display Source modeCD/External disc control mode Switching the Upper Part DisplaySwitching the Lower Part Display Tuner modeCD/External disc control mode Removing the Faceplate Forced ClosingRemoving the faceplate Turning non-fading output On/Off Audio control featuresNon-Fading Output Reattaching the FaceplateBass Quality Factor Audio Control SettingBass Center Frequency Bass LevelMiddle Quality Factor Middle Center FrequencyTreble Level Middle LevelHigh-pass Filter Frequency for Rear Output Phase for Non-Fading OutputVolume Offset High-pass Filter Frequency for Front OutputKDC-X917/X817/9017 Tuner featuresFrequency Station Preset Memory TuningAuto Memory Entry Canceling Direct Access Tuning Direct Access TuningAssigning Names Station Name Preset SnpsStation Name Preset Play Snpp RDS featuresCanceling mode during input Program Type PTY Function AlarmRDS Radio Data System Radio Text ScrollTo register a non-RDS station as a program type Registration of a station as a PTYSeeking the Selected Program Type Confirming Program TypePlaying CDs CD/External disc control featuresFast Forwarding and Reversing Disc Play Playing Other Disc modeTrack Search Track / Disc Repeat Track ScanRandom Play Text Scroll Presetting Disc Names Dnps Magazine Random Play Rapid display forward / reverse Disc Name Preset Play DnppCanceling Direct Disc Search While It Is Operating To cancel Dnpp mode Press the Dnpp buttonMenu System Menu settingsEnter the menu mode Ending the menu mode Press the Menu buttonIf you press the Reset button or remove the battery Security Code In Stand by modeAdjusting the date Manual Time AdjustmentCalendar Adjustment Calendar ModeInputting / Changing the text Memo ModeAutomatic Time Adjustment Entering the month or day setting modeIcon/Spectrum analyzer Select Switching Display ModeBrightness level adjustment Selectable IlluminationDimmer Built-in Amp Mute Control In Stand by modeTime setting for removing the faceplate Dual Zone System In AUX modeExternal Amp Control Switching to a Different Traffic Information StationTraffic Information Function Basic operations Basic Operations of remoteLoading and Replacing the Batteries Tuner features CD/External disc control features Installation Procedure AccessoriesBattery + Connecting Wires to TerminalsLocking the faceplate to the unit Installation non-Japanese carsInstallation non-Japanese cars Locking the faceplate to the unitRemoving the hard rubber frame Removing the UnitRemoving the Unit Installing Radio Bracket in Japanese-made Cars J-Cars Installation Japanese-carsProblem Possible Cause Solution Troubleshooting GuideProblem Possible Cause Solution CD/External disc control mode No Panel CD player section SpecificationsFM tuner section AM tuner section Audio sectionRemarque Ar Audio Page Warranty Card WHO is Protected