Kenwood KDC-X717 instruction manual Problem Possible Cause Solution

Page 49

	PROBLEM	POSSIBLE CAUSE	SOLUTION

	No sound can be heard, or the	Attenuator is turned on.	Turn off Attenuator.
	volume is low.
	volume is low.	The fader or balance settings are set all the way to one	Reset the fader or balance settings.
		The fader or balance settings are set all the way to one	Reset the fader or balance settings.
		side.

		The input/output wires or wiring harness are connected	Reconnect the input/output wires or the wiring harness
		incorrectly.	correctly. See the section on "Connecting Wires to
			Terminals".

		The values of Volume offset are low.	Increase the values of Volume offset. (see p. 18)

	The sound quality is poor or	One of the speaker wires is being pinched by a screw in	Check the speaker wiring.
	distorted.	the car.

		The speakers are not wired correctly.	Reconnect the speaker wires so that each output
			terminal is connected to a different speaker.

	A CD ejects as soon as it is	The CD is upside-down.	Load the CD with the labeled side up.
	loaded.
	loaded.	The CD is quite dirty.	Clean the CD, referring to the section on "Cleaning CDs"
		The CD is quite dirty.	Clean the CD, referring to the section on "Cleaning CDs"
			(see p. 6).

	The sound skips on a CD.	The CD is scratched or dirty.	Clean the CD, referring to the section on "Cleaning CDs"
			(see p. 6).

	A track will not play.	Random play has been selected.	Turn off random play.

Can’t remove disc.

The cause is that more than 10 minutes has elapsed since the vehicle ACC switch was turned OFF.

The disc can only be removed within 10 minutes of the ACC switch being turned OFF. If more than 10 minutes has elapsed, turn the ACC switch ON again and press the Eject button.

— 49 —

Image 49

Contents KDC-X917 KDC-X817 KDC-9017 KDC-X717 Contents 2Warning To prevent injury or fire, take the following precautions Safety precautionsCleaning the Faceplate Terminals Cleaning the CD SlotCleaning the Unit Lens FoggingHandling Compact discs Cleaning CDsStoring CDs Checking New CDs for BurrsRemoving the CD Do Not Load CD AccessoriesDo Not Use Special Shape CDs Do Not Use CDs with Sticker on the Labeled SidePower General featuresPower ON/OFF Switching Modes VolumeAttenuator Switching the Preset Sound Setting Speaker & Woofer settingLoudness System QSwitching Full-Screen Display Faceplate Angle AdjustmentSource mode Stand by modeSwitching the Lower Part Display Switching the Upper Part DisplayTuner mode CD/External disc control modeCD/External disc control mode Removing the Faceplate Forced ClosingRemoving the faceplate Non-Fading Output Audio control featuresReattaching the Faceplate Turning non-fading output On/OffBass Center Frequency Audio Control SettingBass Level Bass Quality FactorTreble Level Middle Center FrequencyMiddle Level Middle Quality FactorVolume Offset Phase for Non-Fading OutputHigh-pass Filter Frequency for Front Output High-pass Filter Frequency for Rear OutputKDC-X917/X817/9017 Tuner featuresFrequency Station Preset Memory TuningAuto Memory Entry Canceling Direct Access Tuning Direct Access TuningAssigning Names Station Name Preset SnpsStation Name Preset Play Snpp RDS featuresCanceling mode during input RDS Radio Data System AlarmRadio Text Scroll Program Type PTY FunctionSeeking the Selected Program Type Registration of a station as a PTYConfirming Program Type To register a non-RDS station as a program typePlaying CDs CD/External disc control featuresFast Forwarding and Reversing Disc Play Playing Other Disc modeTrack Search Track / Disc Repeat Track ScanRandom Play Text Scroll Presetting Disc Names Dnps Magazine Random Play Canceling Direct Disc Search While It Is Operating Disc Name Preset Play DnppTo cancel Dnpp mode Press the Dnpp button Rapid display forward / reverseEnter the menu mode Menu settingsEnding the menu mode Press the Menu button Menu SystemIf you press the Reset button or remove the battery Security Code In Stand by modeCalendar Adjustment Manual Time AdjustmentCalendar Mode Adjusting the dateAutomatic Time Adjustment Memo ModeEntering the month or day setting mode Inputting / Changing the textBrightness level adjustment Switching Display ModeSelectable Illumination Icon/Spectrum analyzer SelectTime setting for removing the faceplate Built-in Amp Mute Control In Stand by modeDual Zone System In AUX mode DimmerExternal Amp Control Switching to a Different Traffic Information StationTraffic Information Function Basic operations Basic Operations of remoteLoading and Replacing the Batteries Tuner features CD/External disc control features Installation Procedure AccessoriesBattery + Connecting Wires to TerminalsInstallation non-Japanese cars Installation non-Japanese carsLocking the faceplate to the unit Locking the faceplate to the unitRemoving the hard rubber frame Removing the UnitRemoving the Unit Installing Radio Bracket in Japanese-made Cars J-Cars Installation Japanese-carsProblem Possible Cause Solution Troubleshooting GuideProblem Possible Cause Solution CD/External disc control mode No Panel FM tuner section SpecificationsAM tuner section Audio section CD player sectionRemarque Ar Audio Page Warranty Card WHO is Protected