Cisco Systems 3120 Accessing the CLI Through the Console Port, Connecting to the Console Port

Page 65

A P P E N D I X C

Configuring the Switch with the CLI-Based

Setup Program

This appendix provides a quick installation and setup procedure for the switch module by using the command-line interface (CLI).

Note For detailed installation procedures, see Chapter 2, “Switch Installation.” For product overview information, see Chapter 1, “Product Overview.”

These are the major steps for a quick installation when using the CLI:

1.Accessing the CLI Through the Console Port, page C-1

2.Connecting to the Console Port, page C-1

3.Completing the Initial Configuration, page C-4

Accessing the CLI Through the Console Port

You can access the CLI on a configured or unconfigured switch module by connecting the console port of the switch module to the serial port on your PC or workstation and accessing the switch module through a Telnet session.

Connecting to the Console Port

Obtain and make note of this information from your network administrator before you begin the switch module installation:

•Switch IP address

•Subnet mask (IP netmask)

•Default gateway (router)

•Enable secret password (encrypted)

•Enable password (not encrypted)

•Telnet password

•SNMP community strings (optional)

Cisco Catalyst Blade Switch 3120 for HP Hardware Installation Guide

	OL-12246-01	C-1

Image 65

Contents Americas Headquarters MarchPage N T E N T S Setup Accessing the CLI Through the Console Port OL-12246-01 Organization AudiencePurpose Related Publications ConventionsPreface OL-12246-01 Product Overview Switch Module Features OverviewPort Description UID 1 LEDSwitch Module Console Port Other FeaturesGigabit Ethernet Module Slots 10/100/1000 PortsCisco TwinGig Converter Module LRMSystem LED LEDsStack LED Color System StatusStack Member LED Stack Master LEDUID and Health LEDs RJ-45 Uplink Port LEDsGigabit Ethernet Module Slot Port LEDs X2 Module Installed Only the CBS3120X SwitchStackWise Plus Ports Power ConnectorsManagement Options Device Manager Using the Device ManagerNetwork Configurations Using the Command-Line InterfacePreparing for Installation Switch InstallationSafety Warnings Installation Guidelines Verifying Package Contents Rear View of the Blade Enclosure HP c-Class BladeSystem Enclosure ArchitectureStatement Installing the Switch Module in the Blade EnclosureOpen the Release Latch Switch Module IP Addresses Switch Installation Onboard Administrator Interconnect Bay Summary Window Express Setup Advanced Settings Table Using Express SetupEnter switch 1 priority Setting the Installed Switch Module As the Stack MasterRefreshing the PC IP Address Planning and Creating a Switch StackStack Cabling Configurations 250304 Connecting to the StackWise Plus Ports Installing Devices in the 10-Gigabit Ethernet Slots Installing a Transceiver or Converter Module Removing a Module 12 Installing X2 Transceiver ModulesInstalling an SFP Module Installing SFP ModulesRemoving an SFP Module 14 Converter Module with SFP Modules Installed15 Connecting to an Ethernet Port Connecting to the 10/100/1000 PortsPlanning 10/100/1000 Ethernet Port Connections Device Crossover Cable Where to Go NextSwitch Installation Where to Go Next Verify the Switch Module Post Results Diagnosing ProblemsConfirm the Switch Module Connections Look at the Switch Module LEDsBad or Damaged Cable Ethernet and Fiber CablesPort and Interface Settings SFP Module Port IssuesPing the End Device Spanning Tree LoopsSpeed, Duplex, and Autonegotiation Verify the Switch Module PerformanceAutonegotiation and Network-Interface Cards Cabling DistanceReplacing a Failed Stack Member Clearing the Switch Module IP Address and Configuration250310 Locating the Switch Module Serial NumberOL-12246-01 Environmental Ranges Physical DimensionsOL-12246-01 Connector Specifications Connector and Cable SpecificationsConnecting to 1000BASE-T Devices Connecting to 10BASE-T- and 100BASE-TX-Compatible DevicesCisco TwinGig Converter Module Ports Gigabit Ethernet Module InterfacesGigabit Ethernet X2 Transceiver Module Cable Specifications Cable and Adapter SpecificationsConsole Port Microns MHz/km DistanceDBm Wavelength nm X2 Product Transmit Power Receive Power NumberTransmit Two Twisted-Pair Cable Pinouts SFP Module Cable Specifications1000BASE-SX GLC-SX-MMTP3 Four Twisted-Pair Cable Pinouts for 1000BASE-T PortsIdentifying a Crossover Cable Switch Console RJ-45-to-DB-9 Port DTEConsole Port Adapter Pinouts DeviceSwitch Console RJ-45-to-DB-25 Port DTE OL-12246-01 Connecting to the Console Port Accessing the CLI Through the Console PortOL-12246-01 Figure C-1 Connecting through the Switch Module Console Port Completing the Initial Configuration To configure Snmp now, enter yes These choices appear CLI NumericsIN-2 Post UIDIN-4 LEDIN-5 IN-6

Related manuals

Manual 70 pages 50.26 Kb