Cisco Systems 3120 manual Verifying Package Contents

Page 24

Chapter 2 Switch Installation

Preparing for Installation

Verifying Package Contents

Carefully remove the contents from the shipping container, and look at each item for damage. If any item is missing or damaged, contact your Cisco representative or reseller for support. Return all packing material to the shipping container, and save it.

These items ship with your switch module. The Cisco TwinGig Converter Modules with installed protective dust covers are shipped already installed on your switch module.

•Console cable

•1-meter Stackwise Plus cable

•Documentation CD that contains:

–Cisco Catalyst Blade Switch 3000 Series for HP Getting Started Guide

–Regulatory Compliance and Safety Information for the Cisco Catalyst Blade Switch 3000 Series for HP

–Cisco and HP Warranty Information

Note If the switch modules are ordered with the blade enclosure, the switch modules are already installed, and no unpacking is required. The unpacking procedure applies only if a switch module is ordered separately.

Cisco Catalyst Blade Switch 3120 for HP Hardware Installation Guide

2-4	OL-12246-01

Image 24

Contents March Americas HeadquartersPage N T E N T S Setup Accessing the CLI Through the Console Port OL-12246-01 Audience PurposeOrganization Conventions Related PublicationsPreface OL-12246-01 Switch Module Features Overview Product OverviewUID 1 LED Port DescriptionOther Features Switch Module Console Port10/100/1000 Ports Gigabit Ethernet Module SlotsCisco TwinGig Converter Module LRMLEDs System LEDStack LED Color System StatusStack Master LED Stack Member LEDUID and Health LEDs RJ-45 Uplink Port LEDsX2 Module Installed Only the CBS3120X Switch Gigabit Ethernet Module Slot Port LEDsPower Connectors Management OptionsStackWise Plus Ports Using the Device Manager Device ManagerUsing the Command-Line Interface Network ConfigurationsSwitch Installation Preparing for InstallationSafety Warnings Installation Guidelines Verifying Package Contents HP c-Class BladeSystem Enclosure Architecture Rear View of the Blade EnclosureInstalling the Switch Module in the Blade Enclosure StatementOpen the Release Latch Switch Module IP Addresses Switch Installation Onboard Administrator Interconnect Bay Summary Window Using Express Setup Express Setup Advanced Settings TableSetting the Installed Switch Module As the Stack Master Enter switch 1 priorityPlanning and Creating a Switch Stack Refreshing the PC IP AddressStack Cabling Configurations 250304 Connecting to the StackWise Plus Ports Installing Devices in the 10-Gigabit Ethernet Slots Installing a Transceiver or Converter Module 12 Installing X2 Transceiver Modules Removing a ModuleInstalling SFP Modules Installing an SFP Module14 Converter Module with SFP Modules Installed Removing an SFP ModuleConnecting to the 10/100/1000 Ports 15 Connecting to an Ethernet PortPlanning 10/100/1000 Ethernet Port Connections Where to Go Next Device Crossover CableSwitch Installation Where to Go Next Diagnosing Problems Verify the Switch Module Post ResultsLook at the Switch Module LEDs Confirm the Switch Module ConnectionsBad or Damaged Cable Ethernet and Fiber CablesSFP Module Port Issues Port and Interface SettingsPing the End Device Spanning Tree LoopsVerify the Switch Module Performance Speed, Duplex, and AutonegotiationAutonegotiation and Network-Interface Cards Cabling DistanceClearing the Switch Module IP Address and Configuration Replacing a Failed Stack MemberLocating the Switch Module Serial Number 250310OL-12246-01 Physical Dimensions Environmental RangesOL-12246-01 Connector and Cable Specifications Connector SpecificationsConnecting to 10BASE-T- and 100BASE-TX-Compatible Devices Connecting to 1000BASE-T DevicesGigabit Ethernet Module Interfaces Cisco TwinGig Converter Module PortsCable and Adapter Specifications Gigabit Ethernet X2 Transceiver Module Cable SpecificationsConsole Port Microns MHz/km DistanceX2 Product Transmit Power Receive Power Number TransmitDBm Wavelength nm SFP Module Cable Specifications Two Twisted-Pair Cable Pinouts1000BASE-SX GLC-SX-MMFour Twisted-Pair Cable Pinouts for 1000BASE-T Ports TP3Switch Console RJ-45-to-DB-9 Port DTE Identifying a Crossover CableConsole Port Adapter Pinouts DeviceSwitch Console RJ-45-to-DB-25 Port DTE OL-12246-01 Accessing the CLI Through the Console Port Connecting to the Console PortOL-12246-01 Figure C-1 Connecting through the Switch Module Console Port Completing the Initial Configuration To configure Snmp now, enter yes These choices appear Numerics CLIIN-2 UID PostLED IN-4IN-5 IN-6

Related manuals

Manual 70 pages 50.26 Kb