Cisco Systems 3120 manual Conventions, Related Publications

Page 8

Preface

Conventions

Appendix B, “Connector and Cable Specifications,” describes the connectors, cables, and adapters that can be used to connect to the switch module.

Appendix C, “Configuring the Switch with the CLI-Based Setup Program,” has an installation and setup procedure for a standalone switch module.

Conventions

This document uses these conventions and symbols for notes, cautions, and warnings:

Note Means reader take note. Notes contain helpful suggestions or references to materials not contained in this manual.

Caution Means reader be careful. In this situation, you might do something that could result in equipment damage or loss of data.

Warning IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. SAVE THESE INSTRUCTIONS (Statement 1071)

The safety warnings for this product are translated into several languages in the Regulatory Compliance and Safety Information for the Cisco Catalyst Blade Switch 3000 Series for HP that ships with the product. The EMC regulatory statements are also included in that guide.

Related Publications

These documents provide complete information about the switch module and are available from this Cisco.com site (they are not orderable):

http://www.cisco.com/en/US/products/ps6748/tsd_products_support_series_home.html

•Cisco Catalyst Blade Switch 3000 Series for HP Getting Started Guide

•Regulatory Compliance and Safety Information for the Cisco Catalyst Blade Switch 3000 Series for HP

•Release Notes for the Cisco Catalyst Blade Switch 3120 for HP

Note Before installing, configuring, or upgrading the switch module, see the release notes on Cisco.com for the latest information.

•Cisco Catalyst Blade Switch 3120 for HP Software Configuration Guide

•Cisco Catalyst Blade Switch 3120 for HP Command Reference

•Cisco Catalyst Blade Switch 3120 for HP System Message Guide

Cisco Catalyst Blade Switch 3120 for HP Hardware Installation Guide

8	OL-12246-01

Image 8

Contents March Americas HeadquartersPage N T E N T S Setup Accessing the CLI Through the Console Port OL-12246-01 Organization AudiencePurpose Conventions Related PublicationsPreface OL-12246-01 Switch Module Features Overview Product OverviewUID 1 LED Port DescriptionOther Features Switch Module Console Port10/100/1000 Ports Gigabit Ethernet Module SlotsCisco TwinGig Converter Module LRMLEDs System LEDStack LED Color System StatusStack Master LED Stack Member LEDUID and Health LEDs RJ-45 Uplink Port LEDsX2 Module Installed Only the CBS3120X Switch Gigabit Ethernet Module Slot Port LEDsStackWise Plus Ports Power ConnectorsManagement Options Using the Device Manager Device ManagerUsing the Command-Line Interface Network ConfigurationsSwitch Installation Preparing for InstallationSafety Warnings Installation Guidelines Verifying Package Contents HP c-Class BladeSystem Enclosure Architecture Rear View of the Blade EnclosureInstalling the Switch Module in the Blade Enclosure StatementOpen the Release Latch Switch Module IP Addresses Switch Installation Onboard Administrator Interconnect Bay Summary Window Using Express Setup Express Setup Advanced Settings TableSetting the Installed Switch Module As the Stack Master Enter switch 1 priorityPlanning and Creating a Switch Stack Refreshing the PC IP AddressStack Cabling Configurations 250304 Connecting to the StackWise Plus Ports Installing Devices in the 10-Gigabit Ethernet Slots Installing a Transceiver or Converter Module 12 Installing X2 Transceiver Modules Removing a ModuleInstalling SFP Modules Installing an SFP Module14 Converter Module with SFP Modules Installed Removing an SFP ModuleConnecting to the 10/100/1000 Ports 15 Connecting to an Ethernet PortPlanning 10/100/1000 Ethernet Port Connections Where to Go Next Device Crossover CableSwitch Installation Where to Go Next Diagnosing Problems Verify the Switch Module Post ResultsLook at the Switch Module LEDs Confirm the Switch Module ConnectionsBad or Damaged Cable Ethernet and Fiber CablesSFP Module Port Issues Port and Interface SettingsPing the End Device Spanning Tree LoopsVerify the Switch Module Performance Speed, Duplex, and AutonegotiationAutonegotiation and Network-Interface Cards Cabling DistanceClearing the Switch Module IP Address and Configuration Replacing a Failed Stack MemberLocating the Switch Module Serial Number 250310OL-12246-01 Physical Dimensions Environmental RangesOL-12246-01 Connector and Cable Specifications Connector SpecificationsConnecting to 10BASE-T- and 100BASE-TX-Compatible Devices Connecting to 1000BASE-T DevicesGigabit Ethernet Module Interfaces Cisco TwinGig Converter Module PortsCable and Adapter Specifications Gigabit Ethernet X2 Transceiver Module Cable SpecificationsConsole Port Microns MHz/km DistanceDBm Wavelength nm X2 Product Transmit Power Receive Power NumberTransmit SFP Module Cable Specifications Two Twisted-Pair Cable Pinouts1000BASE-SX GLC-SX-MMFour Twisted-Pair Cable Pinouts for 1000BASE-T Ports TP3Switch Console RJ-45-to-DB-9 Port DTE Identifying a Crossover CableConsole Port Adapter Pinouts DeviceSwitch Console RJ-45-to-DB-25 Port DTE OL-12246-01 Accessing the CLI Through the Console Port Connecting to the Console PortOL-12246-01 Figure C-1 Connecting through the Switch Module Console Port Completing the Initial Configuration To configure Snmp now, enter yes These choices appear Numerics CLIIN-2 UID PostLED IN-4IN-5 IN-6

Related manuals

Manual 70 pages 50.26 Kb