Cisco Systems 3120 manual Gigabit Ethernet Module Slot Port LEDs

Page 17

Chapter 1 Product Overview

Other Features

Table 1-5 Meaning of Port Link LED Colors

LED Color

Meaning

 

 

Amber

Port disabled, either error or STP1 disabled.

Alternating Green/Amber

Link fault.

 

 

1. STP: Spanning Tree Protocol.

The port activity LED blinks green to indicate traffic.

10-Gigabit Ethernet Module Slot Port LEDs

The behavior of the 10-Gigabit Ethernet module slot port LEDs depends on whether an X2 module or a converter module is installed and whether you pressed the Mode button to place the switch module in stack mode.

X2 Module Installed (Only the CBS3120X Switch)

The 10-Gigabit Ethernet module slot LEDs 19 to 22 show the status for ports 19 to 20 and 21 to 22, respectively (see items 8 and 11 in Figure 1-1 on page 1-2). When an X2 module is installed, each pair of LEDs behaves as one. The top pair of LEDs represents the left X2 module in slot 19 to 20, and the bottom pair of LEDs represents the right X2 module in slot 21 to 22.

Table 1-6describes the 10-Gigabit Ethernet slot port LED colors and their meanings.

Table 1-6

Meaning of 10-Gigabit Ethernet Module Slot LED Colors

 

 

 

LED Color

 

Meaning

 

 

 

Off

 

No link established.

 

 

 

Solid green

 

Link established, no activity.

 

 

 

Blinking green

 

Activity (traffic) on an established link.

 

 

 

Amber

 

Port disabled, either error or STP disabled.

 

 

Alternating green/amber

Link fault.

 

 

 

Converter Module Installed

When a converter module is in one of the 10-Gigabit Ethernet module slots, the LEDs show the status of the SFP modules that are in the converter module. If one converter module is installed in slots 19 and 20, and one converter module is installed in slots 20 and 21, this is how the LEDs correspond to the installed SFP modules:

1.The top LED (19) corresponds to the SFP module in slot 19.

2.The second LED (20) corresponds to the SFP module in slot 20.

3.The third LED (21) corresponds to the SFP module in slot 21.

4.The fourth LED (22) corresponds to the SFP module in slot 22.

See Table 1-6for a description of the 10-Gigabit Ethernet slot port LED colors and their meanings.

Cisco Catalyst Blade Switch 3120 for HP Hardware Installation Guide

 

OL-12246-01

1-7

 

 

 

Image 17
Contents Americas Headquarters MarchPage N T E N T S Setup Accessing the CLI Through the Console Port OL-12246-01 Organization AudiencePurpose Related Publications ConventionsPreface OL-12246-01 Product Overview Switch Module Features OverviewPort Description UID 1 LEDSwitch Module Console Port Other FeaturesGigabit Ethernet Module Slots 10/100/1000 PortsCisco TwinGig Converter Module LRMSystem LED LEDsStack LED Color System StatusStack Member LED Stack Master LEDUID and Health LEDs RJ-45 Uplink Port LEDsGigabit Ethernet Module Slot Port LEDs X2 Module Installed Only the CBS3120X SwitchStackWise Plus Ports Power ConnectorsManagement Options Device Manager Using the Device ManagerNetwork Configurations Using the Command-Line InterfacePreparing for Installation Switch InstallationSafety Warnings Installation Guidelines Verifying Package Contents Rear View of the Blade Enclosure HP c-Class BladeSystem Enclosure ArchitectureStatement Installing the Switch Module in the Blade EnclosureOpen the Release Latch Switch Module IP Addresses Switch Installation Onboard Administrator Interconnect Bay Summary Window Express Setup Advanced Settings Table Using Express SetupEnter switch 1 priority Setting the Installed Switch Module As the Stack MasterRefreshing the PC IP Address Planning and Creating a Switch StackStack Cabling Configurations 250304 Connecting to the StackWise Plus Ports Installing Devices in the 10-Gigabit Ethernet Slots Installing a Transceiver or Converter Module Removing a Module 12 Installing X2 Transceiver ModulesInstalling an SFP Module Installing SFP ModulesRemoving an SFP Module 14 Converter Module with SFP Modules Installed15 Connecting to an Ethernet Port Connecting to the 10/100/1000 PortsPlanning 10/100/1000 Ethernet Port Connections Device Crossover Cable Where to Go NextSwitch Installation Where to Go Next Verify the Switch Module Post Results Diagnosing ProblemsConfirm the Switch Module Connections Look at the Switch Module LEDsBad or Damaged Cable Ethernet and Fiber CablesPort and Interface Settings SFP Module Port IssuesPing the End Device Spanning Tree LoopsSpeed, Duplex, and Autonegotiation Verify the Switch Module PerformanceAutonegotiation and Network-Interface Cards Cabling DistanceReplacing a Failed Stack Member Clearing the Switch Module IP Address and Configuration250310 Locating the Switch Module Serial NumberOL-12246-01 Environmental Ranges Physical DimensionsOL-12246-01 Connector Specifications Connector and Cable SpecificationsConnecting to 1000BASE-T Devices Connecting to 10BASE-T- and 100BASE-TX-Compatible DevicesCisco TwinGig Converter Module Ports Gigabit Ethernet Module InterfacesGigabit Ethernet X2 Transceiver Module Cable Specifications Cable and Adapter SpecificationsConsole Port Microns MHz/km DistanceDBm Wavelength nm X2 Product Transmit Power Receive Power NumberTransmit Two Twisted-Pair Cable Pinouts SFP Module Cable Specifications1000BASE-SX GLC-SX-MMTP3 Four Twisted-Pair Cable Pinouts for 1000BASE-T PortsIdentifying a Crossover Cable Switch Console RJ-45-to-DB-9 Port DTEConsole Port Adapter Pinouts DeviceSwitch Console RJ-45-to-DB-25 Port DTE OL-12246-01 Connecting to the Console Port Accessing the CLI Through the Console PortOL-12246-01 Figure C-1 Connecting through the Switch Module Console Port Completing the Initial Configuration To configure Snmp now, enter yes These choices appear CLI NumericsIN-2 Post UIDIN-4 LEDIN-5 IN-6
Related manuals
Manual 70 pages 50.26 Kb