Samsung SCC-C7439P user manual Installation

Page 11

Installation

1.Press the SNAP FIT of the ADAPTOR in the HOUSING to open the ADAPTOR part, and then insert all external cables into the HOUSING. Secure the HOUSING on the PIPE or MOUNT by turning it clockwise.

(Secure two components tightly, to avoid loosened HOUSING.)

PIPE OR	PIPE OR
MOUNT	MOUNT
HOUSING	HOUSING

EXTERNAL

CABLE

ADAPTOR

SNAP-FIT

2.Connect external cables to the CONNECTORS(ALARM IN, POWER, RS-485, ALARM OUT) and connect the CONNECTOR to the ADAPTOR.

Insert the cable into the FRAME SET, and close the ADAPTOR.

English

	BNC JACK
	HOUSING
	INSULATION
POWER INPUT ALARM OUT	TUBE
POWER INPUT ALARM OUT

ALARM IN

M 

RS-485 EXTERNAL

CABLE

ADAPTOR

Then, wrap the BNC JACK with the INSULATION TUBE, and use an insulation tape to seal up the end of the INSULATION TUBE so that the BNC JACK does not protrude outside of the INSULATION TUBE coating.

For more information about cable connection, refer to Connecting the adaptor cable. (page 19)

English _11

955G-EU1_SCC-C7439P-ENG-1.indd11 11

2009-10-15 8:56:1

Image 11

Contents Smart Dome Camera Overview English Important safety instructions Contents What’s Included FeaturesFrame SET At a GlanceCamera Optional Accessories for Installation Installation & connection955G-EU1SCC-C7439P-ENG-1.indd9 2009-10-15 Cable PrecautionsHousing PreparationInstallation Bush Power BNC Cable Bush 24V CableHousing Mount PIN BushHook Protective Camera Tape Cover 22P Connector Housing RackHousing Camera Screws Cover Dome Gasket Dome Frame SETSamsung Half Samsung Full Initial SetupCamera Address Setup Communication Protocol SetupFactory default is 9600 BPS Baud Rate SetupSetting RS-422A/RS-485 Termination Use pins #5, #6 of SW603 to set the baud rateSame address in the network RS-422A/RS-485 Full Duplex OrganizationCONTROLLER/DVR Power Source Connecting with Other deviceConnecting to a monitor Monitor Alarm Alarm OUTTo connect the controller To connect AlarmTo connect Alarm OUT Adaptor Board Connecting the adaptor cablePower Supply Camera will resume the last run operation How to use the keyboard controllerUsing OSD icons Main Menu Profile EXT Burst DAY ModeNight BurstVPS You can configure the general settings of the camera moduleCamera SET Camera IDBLC With Backlight set to IrisDNR With this, you can adjust the AGC level of aAGC MotionXDR ShutterSENS-UP FlickerlessAny excessively bright area in a night scene will be MASKed You can specify a recording mode according to the sceneDAY/NIGHT SET-AUTO SET are not available Auto Switch or Auto FocusWhite BAL  You can specify Mask 1 and 2 simultaneously955G-EU1SCC-C7439P-ENG-1.indd30 2009-10-15 Digital Zoom Zoom SpeedDisplay Zoom Display P/TPOSI/NEGA SyncAGC Color SUP ReverseAdvanced You can enable the motion detection and tracking functionsWhen multiple motions continue arbitrarily Intelligent VideoDisplay ResolutionAlarm OUT Privacy ZonePreset SET. pages 24 ~ Select the preset numberSelect Position and adjust PAN You can set the Auto PAN, PATTERN, and Auto Play Auto Pan SetupSettings so define them again after the operation Auto SET955G-EU1SCC-C7439P-ENG-1.indd38 2009-10-15 Select the Start and move the camera using pan/tilt/zoom Pattern SetupScan Setup ~ 511 for Preset Auto Play SetupSelect Main MENU-ZONE SET Zone SETYou can set the north direction and the zone coverage Select Main MENU-ALARM SET Alarm SET Auto SET Sets the pattern and scan Other SET Clock SETProportional P/T Factory DefaultsPassword OSD ColorSelect Main MENU-SYSTEM Info CommunicationSystem Info You can check the system informationYou can set the language of the user interface LanguageFunction Key Shortcut KeysWDR SpecificationsSmart Dome Camera INT/LINE LockTilt PAN955G-EU1SCC-C7439P-ENG-2.indd51 2009-10-15 Product Appearance955G-EU1SCC-C7439P-ENG-2.indd52 2009-10-15

Related manuals

Manual 260 pages 56.43 Kb