Samsung SCC-C7439P user manual Overview

Page 2

overview

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit.

This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.

WARNING

To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.

To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions.

WARNING

1.Be sure to use only the standard adapter that is specified in the specification sheet. Using any other adapter could cause fire, electrical shock, or damage to the product.

2.Incorrectly connecting the power supply or replacing battery may cause explosion, fire, electric shock, or damage to the product.

3.Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause abnormal heat generation or fire.

4.Securely plug the power cord into the power receptacle. Insecure connection may cause fire.

5.When installing the camera, fasten it securely and firmly. The fall of camera may cause personal injury.

6.Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers filled with water on top of the camera. Doing so may cause personal injury due to fire, electric shock, or falling objects.

7.Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or electric shock.

_ overview

955G-EU1_SCC-C7439P-ENG-1.indd2 2

2009-10-15 8:55:5

Image 2
Contents Smart Dome Camera Overview English  Important safety instructions Contents Features What’s IncludedFrame SET At a GlanceCamera Installation & connection Optional Accessories for Installation955G-EU1SCC-C7439P-ENG-1.indd9 2009-10-15 Preparation PrecautionsHousing CableInstallation PIN Bush Power BNC Cable Bush 24V CableHousing Mount BushFrame SET 22P Connector Housing RackHousing Camera Screws Cover Dome Gasket Dome Hook Protective Camera Tape CoverCommunication Protocol Setup Initial SetupCamera Address Setup Samsung Half Samsung FullUse pins #5, #6 of SW603 to set the baud rate Baud Rate SetupSetting RS-422A/RS-485 Termination Factory default is 9600 BPSRS-422A/RS-485 Full Duplex Organization Same address in the networkMonitor Alarm Alarm OUT Connecting with Other deviceConnecting to a monitor CONTROLLER/DVR Power SourceTo connect the controller To connect AlarmTo connect Alarm OUT Adaptor Board Connecting the adaptor cablePower Supply Camera will resume the last run operation How to use the keyboard controllerUsing OSD icons Main Menu Profile Burst DAY ModeNight EXT BurstCamera ID You can configure the general settings of the camera moduleCamera SET VPSIris BLC With Backlight set toMotion With this, you can adjust the AGC level of aAGC DNRFlickerless ShutterSENS-UP XDRAny excessively bright area in a night scene will be MASKed You can specify a recording mode according to the sceneDAY/NIGHT  You can specify Mask 1 and 2 simultaneously Auto Switch or Auto FocusWhite BAL SET-AUTO SET are not available955G-EU1SCC-C7439P-ENG-1.indd30 2009-10-15 Display P/T Zoom SpeedDisplay Zoom Digital ZoomReverse SyncAGC Color SUP POSI/NEGAIntelligent Video You can enable the motion detection and tracking functionsWhen multiple motions continue arbitrarily AdvancedPrivacy Zone ResolutionAlarm OUT DisplayPreset SET. pages 24 ~ Select the preset numberSelect Position and adjust PAN Auto SET Auto Pan SetupSettings so define them again after the operation You can set the Auto PAN, PATTERN, and Auto Play955G-EU1SCC-C7439P-ENG-1.indd38 2009-10-15 Select the Start and move the camera using pan/tilt/zoom Pattern SetupScan Setup Auto Play Setup ~ 511 for PresetSelect Main MENU-ZONE SET Zone SETYou can set the north direction and the zone coverage Alarm SET Select Main MENU-ALARM SET Auto SET Sets the pattern and scan Clock SET Other SETOSD Color Factory DefaultsPassword Proportional P/TYou can check the system information CommunicationSystem Info Select Main MENU-SYSTEM InfoLanguage You can set the language of the user interfaceShortcut Keys Function KeyINT/LINE Lock SpecificationsSmart Dome Camera WDRPAN TiltProduct Appearance 955G-EU1SCC-C7439P-ENG-2.indd51 2009-10-15955G-EU1SCC-C7439P-ENG-2.indd52 2009-10-15
Related manuals
Manual 260 pages 56.43 Kb