Samsung user manual 955G-EU1SCC-C7439P-ENG-1.indd38 2009-10-15

Page 38

setup

3.Select each item and set appropriately.

POSITION : Set the starting and ending positions for the <AUTO PAN>.

Move to the setting screen and adjust pan/tilt to the desired starting position, and then press [ENTER].

Again, adjust pan/tilt to the desired ending position and press [ENTER] to finish <AUTO PAN> setup.

 

AUTO PAN 1

POSITION

 

DIRECTION

LEFT

ENDLESS

OFF

SPEED

[10]

DWELL TIME

3SEC

DIRECTION : Sets the direction of the camera’s movement from the starting to the end position. (Based on panning)

<RIGHT><LEFT>

START

START

END

END

ENDLESS : Instead of shuttling between start and end positions, the camera turns 360° endlessly while stops for the <DWELL TIME> at both positions.

SPEED : Sets the moving speed of the camera, from 1 to 64.

DWELL TIME : Sets the dwell time at the starting and ending positions, from 1 to 60 seconds.

38_ setup

955G-EU1_SCC-C7439P-ENG-1.indd38 38

2009-10-15 8:56:2

Image 38
Contents Smart Dome Camera Overview English  Important safety instructions Contents Features What’s IncludedFrame SET At a GlanceCamera Installation & connection Optional Accessories for Installation955G-EU1SCC-C7439P-ENG-1.indd9 2009-10-15 Preparation PrecautionsHousing CableInstallation PIN Bush Power BNC Cable Bush 24V CableHousing Mount BushFrame SET 22P Connector Housing RackHousing Camera Screws Cover Dome Gasket Dome Hook Protective Camera Tape CoverCommunication Protocol Setup Initial SetupCamera Address Setup Samsung Half Samsung FullUse pins #5, #6 of SW603 to set the baud rate Baud Rate SetupSetting RS-422A/RS-485 Termination Factory default is 9600 BPSRS-422A/RS-485 Full Duplex Organization Same address in the networkMonitor Alarm Alarm OUT Connecting with Other deviceConnecting to a monitor CONTROLLER/DVR Power SourceTo connect the controller To connect AlarmTo connect Alarm OUT Adaptor Board Connecting the adaptor cablePower Supply Camera will resume the last run operation How to use the keyboard controllerUsing OSD icons Main Menu Profile Burst DAY ModeNight EXT BurstCamera ID You can configure the general settings of the camera moduleCamera SET VPSIris BLC With Backlight set toMotion With this, you can adjust the AGC level of aAGC DNRFlickerless ShutterSENS-UP XDRAny excessively bright area in a night scene will be MASKed You can specify a recording mode according to the sceneDAY/NIGHT  You can specify Mask 1 and 2 simultaneously Auto Switch or Auto FocusWhite BAL SET-AUTO SET are not available955G-EU1SCC-C7439P-ENG-1.indd30 2009-10-15 Display P/T Zoom SpeedDisplay Zoom Digital ZoomReverse SyncAGC Color SUP POSI/NEGAIntelligent Video You can enable the motion detection and tracking functionsWhen multiple motions continue arbitrarily AdvancedPrivacy Zone ResolutionAlarm OUT DisplayPreset SET. pages 24 ~ Select the preset numberSelect Position and adjust PAN Auto SET Auto Pan SetupSettings so define them again after the operation You can set the Auto PAN, PATTERN, and Auto Play955G-EU1SCC-C7439P-ENG-1.indd38 2009-10-15 Select the Start and move the camera using pan/tilt/zoom Pattern SetupScan Setup Auto Play Setup ~ 511 for PresetSelect Main MENU-ZONE SET Zone SETYou can set the north direction and the zone coverage Alarm SET Select Main MENU-ALARM SET Auto SET Sets the pattern and scan Clock SET Other SETOSD Color Factory DefaultsPassword Proportional P/TYou can check the system information CommunicationSystem Info Select Main MENU-SYSTEM InfoLanguage You can set the language of the user interfaceShortcut Keys Function KeyINT/LINE Lock SpecificationsSmart Dome Camera WDRPAN TiltProduct Appearance 955G-EU1SCC-C7439P-ENG-2.indd51 2009-10-15955G-EU1SCC-C7439P-ENG-2.indd52 2009-10-15
Related manuals
Manual 260 pages 56.43 Kb