Samsung SCC-C7439P user manual Power BNC Cable Bush 24V Cable, PIN Bush, Housing Mount

Page 12

installation & connection

Note that BUSHINGs are provided for outdoor installations where exposed to a moisture condition through the PIPE or MOUNT, install the HOUSING using the BUSHING to prevent moisture entering.

-Apply grease of proper dose on the BUSHING before assembling, and run cables through each hole of the bushings. Use PINS to stop up empty holes having no cable running.

-Assemble the BUSHING to the top side of HOUSING’s inside as shown in the diagram below. At the moment, apply pressure evenly on the BUSHING to secure it tightly to the HOUSING as shown in the diagram.

POWER

BNC CABLE

BUSH

(24V) CABLE

BUSH	ETC CABLE

BUSH



BUSH	PIPE OR
HOUSING	MOUNT

HOUSING

BUSH

12_ installation & connection

955G-EU1_SCC-C7439P-ENG-1.indd12 12

2009-10-15 8:56:1

Image 12

Contents Smart Dome Camera Overview English Important safety instructions Contents Features What’s IncludedAt a Glance CameraFrame SET Installation & connection Optional Accessories for Installation955G-EU1SCC-C7439P-ENG-1.indd9 2009-10-15 Precautions HousingPreparation CableInstallation Power BNC Cable Bush 24V Cable Housing MountPIN Bush Bush22P Connector Housing Rack Housing Camera Screws Cover Dome Gasket DomeFrame SET Hook Protective Camera Tape CoverInitial Setup Camera Address SetupCommunication Protocol Setup Samsung Half Samsung FullBaud Rate Setup Setting RS-422A/RS-485 TerminationUse pins #5, #6 of SW603 to set the baud rate Factory default is 9600 BPSRS-422A/RS-485 Full Duplex Organization Same address in the networkConnecting with Other device Connecting to a monitorMonitor Alarm Alarm OUT CONTROLLER/DVR Power SourceTo connect Alarm To connect Alarm OUTTo connect the controller Connecting the adaptor cable Power SupplyAdaptor Board How to use the keyboard controller Using OSD iconsCamera will resume the last run operation Main Menu Profile DAY Mode NightBurst EXT BurstYou can configure the general settings of the camera module Camera SETCamera ID VPSIris BLC With Backlight set toWith this, you can adjust the AGC level of a AGCMotion DNRShutter SENS-UPFlickerless XDRYou can specify a recording mode according to the scene DAY/NIGHTAny excessively bright area in a night scene will be MASKed Auto Switch or Auto Focus White BAL You can specify Mask 1 and 2 simultaneously SET-AUTO SET are not available955G-EU1SCC-C7439P-ENG-1.indd30 2009-10-15 Zoom Speed Display ZoomDisplay P/T Digital ZoomSync AGC Color SUPReverse POSI/NEGAYou can enable the motion detection and tracking functions When multiple motions continue arbitrarilyIntelligent Video AdvancedResolution Alarm OUTPrivacy Zone DisplayPreset Select the preset number Select Position and adjust PANSET. pages 24 ~ Auto Pan Setup Settings so define them again after the operationAuto SET You can set the Auto PAN, PATTERN, and Auto Play955G-EU1SCC-C7439P-ENG-1.indd38 2009-10-15 Pattern Setup Scan SetupSelect the Start and move the camera using pan/tilt/zoom Auto Play Setup ~ 511 for PresetZone SET You can set the north direction and the zone coverageSelect Main MENU-ZONE SET Alarm SET Select Main MENU-ALARM SET Auto SET Sets the pattern and scan Clock SET Other SETFactory Defaults PasswordOSD Color Proportional P/TCommunication System InfoYou can check the system information Select Main MENU-SYSTEM InfoLanguage You can set the language of the user interfaceShortcut Keys Function KeySpecifications Smart Dome CameraINT/LINE Lock WDRPAN TiltProduct Appearance 955G-EU1SCC-C7439P-ENG-2.indd51 2009-10-15955G-EU1SCC-C7439P-ENG-2.indd52 2009-10-15

Related manuals

Manual 260 pages 56.43 Kb