Samsung SCC-C7439P 22P Connector Housing Rack, Frame SET, Hook Protective Camera Tape Cover

Page 13

3.Tie up the SAFETY WIRE of the CAMERA on the BRACKET WIRE of the FRAME SET.

Arrange the 22P CONNECTOR of the CAMERA in line with that of the ADAPTOR, push the HOOKs on either end of the CAMERA in the RACK direction of the FRAME SET to secure the two.

Then, ensure that all of the two HOOKs clicks to fix to the RACK properly.

22P CONNECTOR

HOUSING

 

RACK

RACK

BRACKET WIRE

 

FRAME SET

 

SAFETY WIRE

 

HOOK

PROTECTIVE

CAMERA

TAPE

 

PROTECTIVE

 

COVER

 

HOOK

M

When the installation is completed, remove the PROTECTIVE COVER and

 

PRETOECTIVE TAPE from the lens.

4.Align each of the 3 SCREWS of COVER DOME and 3 SCREW HOLEs of the HOUSING respectively, and assemble the COVER DOME and HOUSING. During the assembling, note on the followings.

Insert and arrange SAFETY WIRE into the HOUSING while not disturbing the camera operation.

Ensure that the GASKET DOME component does not separate from the COVER DOME. (If the GASKET DOME is not properly assembled, it damages the waterproofness.)

English

 

SAFETY WIRE

HOUSING

HOUSING

 

CAMERA

SCREWS

 

COVER DOME

GASKET DOME

COVER DOME

 

English _13

955G-EU1_SCC-C7439P-ENG-1.indd13 13

2009-10-15 8:56:1

Image 13
Contents Smart Dome Camera Overview English  Important safety instructions Contents What’s Included FeaturesCamera At a GlanceFrame SET Optional Accessories for Installation Installation & connection955G-EU1SCC-C7439P-ENG-1.indd9 2009-10-15 Housing PrecautionsPreparation CableInstallation Housing Mount Power BNC Cable Bush 24V CablePIN Bush BushHousing Camera Screws Cover Dome Gasket Dome 22P Connector Housing RackFrame SET Hook Protective Camera Tape CoverCamera Address Setup Initial SetupCommunication Protocol Setup Samsung Half Samsung FullSetting RS-422A/RS-485 Termination Baud Rate SetupUse pins #5, #6 of SW603 to set the baud rate Factory default is 9600 BPSSame address in the network RS-422A/RS-485 Full Duplex OrganizationConnecting to a monitor Connecting with Other deviceMonitor Alarm Alarm OUT CONTROLLER/DVR Power SourceTo connect Alarm OUT To connect AlarmTo connect the controller Power Supply Connecting the adaptor cableAdaptor Board Using OSD icons How to use the keyboard controllerCamera will resume the last run operation Main Menu Profile Night DAY ModeBurst EXT BurstCamera SET You can configure the general settings of the camera moduleCamera ID VPSBLC With Backlight set to IrisAGC With this, you can adjust the AGC level of aMotion DNRSENS-UP ShutterFlickerless XDRDAY/NIGHT You can specify a recording mode according to the sceneAny excessively bright area in a night scene will be MASKed White BAL Auto Switch or Auto Focus You can specify Mask 1 and 2 simultaneously SET-AUTO SET are not available955G-EU1SCC-C7439P-ENG-1.indd30 2009-10-15 Display Zoom Zoom SpeedDisplay P/T Digital ZoomAGC Color SUP SyncReverse POSI/NEGAWhen multiple motions continue arbitrarily You can enable the motion detection and tracking functionsIntelligent Video AdvancedAlarm OUT ResolutionPrivacy Zone DisplayPreset Select Position and adjust PAN Select the preset numberSET. pages 24 ~ Settings so define them again after the operation Auto Pan SetupAuto SET You can set the Auto PAN, PATTERN, and Auto Play955G-EU1SCC-C7439P-ENG-1.indd38 2009-10-15 Scan Setup Pattern SetupSelect the Start and move the camera using pan/tilt/zoom ~ 511 for Preset Auto Play SetupYou can set the north direction and the zone coverage Zone SETSelect Main MENU-ZONE SET Select Main MENU-ALARM SET Alarm SET Auto SET Sets the pattern and scan Other SET Clock SETPassword Factory DefaultsOSD Color Proportional P/TSystem Info CommunicationYou can check the system information Select Main MENU-SYSTEM InfoYou can set the language of the user interface LanguageFunction Key Shortcut KeysSmart Dome Camera SpecificationsINT/LINE Lock WDRTilt PAN955G-EU1SCC-C7439P-ENG-2.indd51 2009-10-15 Product Appearance955G-EU1SCC-C7439P-ENG-2.indd52 2009-10-15
Related manuals
Manual 260 pages 56.43 Kb