Samsung SCC-C7439P user manual To connect Alarm OUT, To connect the controller

Page 18

installation & connection

To connect ALARM IN

1.Connect one end of the external device's signal line to a corresponding ALARM IN port of the monitor.

2.Connect the other end of the signal line to the earth-grounding [GND] port.

To connect ALARM OUT

1.Connect one end of the external device's signal line to a corresponding ALARM OUT port of the monitor.

2.Connect the other end of the signal line to the common [COM] port.

To connect the controller

Connect an external controller or DVR to the camera, with which you can adjust the camera.

1.Connect the Rx+ pin of the camera to the Tx+ pin of the controller.

2.Connect the Rx- pin of the camera to the Tx- pin of the controller.

3.Connect the Tx+ pin of the camera to the Rx+ pin of the controller.

4.Connect the Tx- pin of the camera to the Rx- pin of the controller.

Rx Tx

18_ installation & connection

955G-EU1_SCC-C7439P-ENG-1.indd18 18

2009-10-15 8:56:2

Image 18

Contents Smart Dome Camera Overview English Important safety instructions Contents Features What’s IncludedAt a Glance CameraFrame SET Installation & connection Optional Accessories for Installation955G-EU1SCC-C7439P-ENG-1.indd9 2009-10-15 Preparation PrecautionsHousing CableInstallation PIN Bush Power BNC Cable Bush 24V CableHousing Mount BushFrame SET 22P Connector Housing RackHousing Camera Screws Cover Dome Gasket Dome Hook Protective Camera Tape CoverCommunication Protocol Setup Initial SetupCamera Address Setup Samsung Half Samsung FullUse pins #5, #6 of SW603 to set the baud rate Baud Rate SetupSetting RS-422A/RS-485 Termination Factory default is 9600 BPSRS-422A/RS-485 Full Duplex Organization Same address in the networkMonitor Alarm Alarm OUT Connecting with Other deviceConnecting to a monitor CONTROLLER/DVR Power SourceTo connect Alarm To connect Alarm OUTTo connect the controller Connecting the adaptor cable Power SupplyAdaptor Board How to use the keyboard controller Using OSD iconsCamera will resume the last run operation Main Menu Profile Burst DAY ModeNight EXT BurstCamera ID You can configure the general settings of the camera moduleCamera SET VPSIris BLC With Backlight set toMotion With this, you can adjust the AGC level of aAGC DNRFlickerless ShutterSENS-UP XDRYou can specify a recording mode according to the scene DAY/NIGHTAny excessively bright area in a night scene will be MASKed  You can specify Mask 1 and 2 simultaneously Auto Switch or Auto FocusWhite BAL SET-AUTO SET are not available955G-EU1SCC-C7439P-ENG-1.indd30 2009-10-15 Display P/T Zoom SpeedDisplay Zoom Digital ZoomReverse SyncAGC Color SUP POSI/NEGAIntelligent Video You can enable the motion detection and tracking functionsWhen multiple motions continue arbitrarily AdvancedPrivacy Zone ResolutionAlarm OUT DisplayPreset Select the preset number Select Position and adjust PANSET. pages 24 ~ Auto SET Auto Pan SetupSettings so define them again after the operation You can set the Auto PAN, PATTERN, and Auto Play955G-EU1SCC-C7439P-ENG-1.indd38 2009-10-15 Pattern Setup Scan SetupSelect the Start and move the camera using pan/tilt/zoom Auto Play Setup ~ 511 for PresetZone SET You can set the north direction and the zone coverageSelect Main MENU-ZONE SET Alarm SET Select Main MENU-ALARM SET Auto SET Sets the pattern and scan Clock SET Other SETOSD Color Factory DefaultsPassword Proportional P/TYou can check the system information CommunicationSystem Info Select Main MENU-SYSTEM InfoLanguage You can set the language of the user interfaceShortcut Keys Function KeyINT/LINE Lock SpecificationsSmart Dome Camera WDRPAN TiltProduct Appearance 955G-EU1SCC-C7439P-ENG-2.indd51 2009-10-15955G-EU1SCC-C7439P-ENG-2.indd52 2009-10-15

Related manuals

Manual 260 pages 56.43 Kb