Philips MCM204 user manual Important notes for users in the U.K, Mains plug, How to connect a plug

Page 2

Important notes for users in the U.K.

Mains plug

This apparatus is fitted with an approved 13 Amp plug. To change a fuse in this type of plug proceed as follows:

1Remove fuse cover and fuse.

2Fix new fuse which should be a BS1362 3 Amp, A.S.T.A. or BSI approved type.

3Refit the fuse cover.

If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place.

If the mains plug contains a fuse, this should have a value of 3 Amp. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 3 Amp.

Note: The severed plug must be disposed of to avoid a possible shock hazard should it be inserted into a 13 Amp socket elsewhere.

How to connect a plug

The wires in the mains lead are coloured with the following code: blue = neutral (N), brown = live (L).

As these colours may not correspond with the colour markings identifying the terminals in your plug, proceed as follows:

Connect the blue wire to the terminal marked N or coloured black.

Connect the brown wire to the terminal marked L or coloured red.

Do not connect either wire to the earth terminal in the plug, marked E (or e) or coloured green (or green and yellow).

Before replacing the plug cover, make certain that the cord grip is clamped over the sheath of the lead - not simply over the two wires.

Copyright in the U.K.

Recording and playback of material may require consent. See Copyright Act 1956 and The Performer’s Protection Acts 1958 to 1972.

Italia

DICHIARAZIONE DI CONFORMITA’

Si dichiara che l’apparecchio MCM204 Philips risponde alle prescrizioni dell’art. 2 comma 1 del D.M. 28 Agosto 1995 n. 548.

Fatto a Eindhoven

Philips Consumer Electronics

Philips, Glaslaan 2

5616 JB Eindhoven,The Netherlands

Norge

Typeskilt finnes på apparatens underside.

Observer: Nettbryteren er sekundert innkoplet. Den innebygde netdelen er derfor ikke frakoplet nettet sŒ lenge apparatet er tilsluttet nettkontakten.

For å redusere faren for brann eller elektrisk støt, skal apparatet ikke utsettes for regn eller fuktighet.

CAUTION

Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation.

2

Image 2
Contents Micro Hi-Fi System MCM204Mains plug How to connect a plugImportant notes for users in the U.K Copyright in the U.KPage Klass 1 laseraparat 139 101120 158Contents General Information Supplied accessoriesSafety Information Environmental InformationTo establish a safe volume level Hearing SafetyListen at a moderate volume Set your volume control at a low settingRear connections PowerPreparations MW AntennaFM Antenna Before using the remote controlReplacing battery lithium CR2025 into the remote control Speakers Connection Front SpeakersControls on the system and remote control Controls available on the remote control onlyBasic Functions Switching the system onPower-saving automatic standby Adjusting volume and sound Basic playback controls CD/MP3 OperationLoading a disc Playing an MP3 discReviewing the programme Different play modes Shuffle and RepeatProgramming track numbers Erasing the programmeRadio Reception Tuning to radio stationsTuning to preset radio stations Programming radio stationsGeneral information on recording Synchro start CD recording Tape Operation / RecordingTape playback To select and record a particular passage within a CD trackListening to an external source Other ConnectionRecording from the radio Supported formats Using USB connectivityUSB Connection System will not play or support the followingInformation Regarding USB Direct Setting the timer Clock/TimerSetting the clock Activating and deactivatingSpecifications MaintenanceTroubleshooting Check the speaker connections and locationProperly Remote control does not functionClock/Timer setting is erased Time is not workingFrançais Meet Philips at the Internet