Orion Car Audio XTR1002 owner manual Installing the Crossover, To Tweeter

Page 7

INSTALLING THE CROSSOVER

There is a tweeter level jumper for adjusting the tweeter. Cutting this jumper will change the output gain of the tweeter. Where the adjustment should be depends on the location of the tweeter and your preference. Adjustments can be made from 0dB to -3dB by cutting the "level jumper". Tweeter phase can be changed by reversing the polarity of the amplifier output wire connections to the crossover. If the tweeter is within 6" of the woofer center the tweeter should be in phase with the woofer. If the tweeter is further than 6" from the center of the woofer, both in phase and out of phase should be tried to see which is best.

Use wire tie or screws to secure crossover housing in place.

Figure 3

To Tweeter

Figura 3

 

Abbildung 3

 

-

+

Level jumper

Crossover

Note: Jumper is under top cover of crossover housing.

Remarque : Le cavalier se trouve sous le couvercle du boîtier du filtre.

Nota: El puente está debajo de la tapa de arriba del alojamiento del crossover.

Hinweis: Der Jumper befindet sich unter dem Deckel des Crossover-Gehäuses.

Nota: il ponticello si trova sotto il coperchio superiore del supporto del crossover

Nota: O jumper está embaixo da tampa superior da carcaça do crossover.

Amplifier

+

_

Note: The tweeter positive is the wire marked with the stripe.

Note: Le câble positif du haut-parleur d'aigus est rayé.

Nota. El positivo del tweeter es el cable que tiene la franja.

Hinweis: Der positive Hochtönerdraht ist mit dem Streifen markiert.

Nota: il filo positivo del tweeter è contrassegnato da una striscia.

Nota: O cabo positivo do tweeter está marcado com a listra.

6

© 2008 directed electronics—all rights reserved

Page 6 Page 8
Image 7
Page 6 Page 8
Contents
Component Speaker Introduction Table of ContentsWHAT’S in the BOX Practice Safe SoundTools of the Trade Rear Deck Mounting InstallationFinding Speaker Mounting Locations Door MountingSurface Mounting Installing the TweetersFigura Full Flush MountingTo Tweeter Installing the CrossoverFeatures SpecificationsPage Montage SUR LA Plage Arrière Choix DES Emplacements DE Montage DES HAUT- ParleursFrançais Montage Dans LA PorteMontage EN Surface Installation DES HAUT-PARLEURS D’AIGUSMontage Totalement Encastré Installation DU Filtre Caractéristiques SpécificationsModèle XTR1002 Montaje EN LA Repisa Trasera EspañolUbicaciones DE Montaje DE LOS Altavoces Montaje EN LA PuertaMontaje AL RAS Consulte el diagrama de las páginas 4-6 figura 1,2,3Instalación DE LOS Tweeters Montaje EN SuperficieInstalación DEL Crossover Características EspecificacionesModelo XTR1002 Einbau IM Kofferraum DeutschSO Platzieren SIE DIE Lautsprecher TüreinbauKabelbaum Installation DER HochtönerSiehe Diagramm auf Seite 4-6 Abbildung 1, 2 OberflächeneinbauInstallation DER CROSSOVER-EINHEIT Merkmale Technische DatenModell XTR1002 Montaggio Sulle Portiere ItalianoMontaggio a Filo Installazione DEI TweeterVedere lo schema a pagina 4 6 Figura 1,2,3 Fissaggio SU UNA SuperficieInstallazione DEL Crossover Caratteristiche Dati TecniciModello XTR1002 Instalação no Painel Traseiro PortuguêsDeterminação DOS Locais DE Instalação DOS ALTOS-FALANTES Instalação NAS PortasInstalação Embutida Consulte o diagrama nas páginas 4 6 Figura 1,2,3Instalação DOS Tweeters Instalação NA SuperfícieInstalação do Crossover Especificações Warranty
Related manuals
Manual 30 pages 52.17 Kb