5. SOUND PARAMETER
The NIGHT mode, the Dolby PLII MUSIC and NEO:6 PARAMETER are set by following the steps below.
SOUND PARAMETER
>NIGHT | MODE |
DOLBY | PLI MUSIC |
NEO:6 | PARAMETER |
RETURN TO MAIN MENU
5-1 NIGHT MODE
In the NIGHT mode, the dynamic range of the sound played is reduced, making it possible to listen more clearly to a softer sound while keeping the overall volume level relatively low at night or in similar circumstances. This mode works only with Dolby digital sound.
1. Press the 3/4 cursor buttons to move the cursor to NIGHT MODE on the SOUND PARAMETER menu, and when the selection is entered using the ENTER button, a sub- menu appears.
NIGHT | MODE |
>DRC | : AUTO |
RETURN TO SETUP MENU
2. Press the 1/2 cursor buttons to set AUTO or set the compression rate from 0.0 to 1.0.
•When AUTO is set, the signals contained in the Dolby TrueHD software are detected, and the NIGHT mode is automatically activated. The NIGHT mode is deactivated with any Dolby digital sound signals that are not Dolby TrueHD signals.
•When the compression rate is set to 0.0, the NIGHT mode function is deactivated.
•When the NIGHT mode is activated, the parameter is set in
3. When all the settings have been completed, press the 3/4 cursor buttons to move the cursor to RETURN TO SETUP MENU, and press the ENTER button to return to SOUND PARAMETER menu.
5-2 DOLBY PLII MUSIC
The Dolby PLII MUSIC mode creates an environment for playing CDs and other stereo sources in which the listener is enveloped by a full and rich sound.
1. Press the 3/4 cursor buttons to move the cursor to DOLBY PLII MUSIC on the SOUND PARAMETER menu, and when the selection is entered using the ENTER button, a
DOLBY PLI MUSIC
>PANORAMA | :OFF | |
CENTER WIDTH | : | 3 |
DIMENSION | : | 0 |
RETURN TO SETUP MENU
PANORAMA:
In the PANORAMA mode, the sound delivered from the front left and right speakers envelops the listener to create a
Press the 1/2 cursor buttons to set the PANORAMA mode to ON or OFF.
CENTER WIDTH:
This function gradually assigns the center channel components to the front left and right speakers. By assigning them in this way, inconsistencies in the tone colors between the speakers can be smoothed out.
Adjustment in eight steps from 0 to 7 is possible using the 1/2 cursor buttons.
This setting cannot be selected if NO has been selected as the center speaker setting.
DIMENSION:
The DIMENSION function is used to adjust level differences between the front and rear. Depending on the input source, some sound is heard more strongly at the front and others more strongly at the rear. When this function is used, the desired balance can be achieved.
Adjustment in seven steps from
2. When all the settings have been completed, press the 3/4 cursor buttons to move the cursor to RETURN TO SETUP MENU, and press the ENTER button to return to the SOUND PARAMETER menu.
5-3 NEO:6 PARAMETER
The DTS NEO:6 mode allows the sound of up to
6.1channels to be output when
In this mode, the sound images of the center speaker are expanded.
1.Press the 3/4 cursor buttons to select NEO:6 PARAMETER.
2.Press the ENTER button to enter the selection.
NEO:6 PARAMETER
CENTER GAIN : 0 . 3
RETURN TO SETUP MENU
3. The CENTER GAIN level can be selected in
0.1increments from 0.0 to 1.0 using the 1/2 cursor buttons.
Notes
•This setting takes effect only in the NEO:6 MUSIC mode.
4. When all the settings have been completed, press the 3/4 cursor buttons to move the cursor to RETURN TO SETUP MENU, and press the ENTER button.
ENGLISH
SETUP | FUNCTIONS |
NAMESAND | |
BASIC | CONNECTIONS |
BASIC | OPERATION |
ADVANCED | CONNECTIONS |
SETUP | |
ADVANCED | OPERATION |
TROUBLESHOOTING | |
OTHERS | |
25