Marantz NR1501 manual Video, Hdmi

ENGLISH

NAMESAND FUNCTIONS	TROUBLESHOOTING
	VIDEO
	Symptom	Cause	Solution	Page
BASIC CONNECTIONS		• The monitor TV connection,	• See the monitor TV's instruction
		input switching, etc., are not set	manual.
	No image on the	up correctly.
		• The unit has an HDMI	• Make an HDMI connection to	11
	monitor TV.
		connection to the source	the monitor TV.
		component, but no HDMI
		connection to the monitor TV.
	The audio or		Connect the cables properly,
BASIC OPERATION	the image does	The input cables are not correctly		9, 10, 11
			component jack matches the
		• The video recording component
	not match the	connected.	referring to the connection
	selected source.		diagram.
			• Make sure the recording
	Cannot record to a	jack does not match the source	source component jack. (Video
		component jack.	input)	10
ADVANCED CONNECTIONS	VCR, etc.
		performed by the video deck, the	Connect a monitor TV using the
	The converted
		• A copy-protected signal is being	• Video signals that include copy-
		received.	protected signals cannot be
			recorded.
		When special playback is
	video signals are	conversion may not be carried out	same format (video or component)	10
		normally, causing the video signals
	disturbed.	to be disturbed and preventing the	as the source component.
SETUP		images from being shown.
ADVANCED OPERATION
TROUBLESHOOTING
OTHERS

HDMI

Symptom	Cause	Solution	Page
	The HDMI cable is improperly	Check the HDMI cable connection.	11
	connected.
		Use of a cable no longer than 5
	The unit is connected with a non-	meters is recommended to ensure	11
	spec HDMI cable.	stable operation, prevent picture
		degradation, etc.
	The connection between	Turn the power on again to all
	components over an HDMI
		the components on the HDMI	−
	connection has not been
		connection.
	authenticated.
		Make sure the unit’s HDMI	−
		settings are correct.
		Set the unit for HDMI input, as
		explained in the instruction manual	−
There is no picture		of the video component (TV,
		projector, etc.).
with the HDMI
		Make settings to enable HDMI
connection.
	The HDMI settings are incorrect.	output, as explained in the
		instruction manual of the source	19
		device (Blu-ray disc player, Set Top
		Box, etc.).
		Match the resolution for both
		components, as explained
		in the instruction manual of	−
		the component on the HDMI
		connection.
	The unit is connected to the video	Connect an HDCP-compatible
	component (TV, projector, etc.) by		−
		video component.
	DVI connector.
	The power to the unit is turned off.
	(HDMI connections are not enabled	Turn on the main power to the unit.	12
	when the unit is in STANDBY mode.)
It takes time for	The connection is being	Some HDMI components require
the image to be
	authenticated between components	time for authentication. There is	−
displayed over an
	on the HDMI connection.	nothing wrong with the unit.
HDMI connection.
		Make settings to enable HDMI audio
		output, as explained in the instruction	19
		manual of the source device (Blu-ray
		disc player, Set Top Box, etc.).
	The HDMI settings are incorrect.	Set so that the HDMI audio output
There is no audio		setting matches the signals
		supported by the unit, as explained	−
playback over an
		in the instruction manual of the
HDMI connection.
		source device (Blu-ray disc player,
		Set Top Box, etc.).
		No sound is heard from the unit
	ON has been set for HDMI AUDIO	when ON is set for HDMI AUDIO	19
	OUT on the SYSTEM SETUP menu.	OUT. Select OFF as this menu
		item's setting.

36