Panasonic CQ-5335U operating instructions Speaker Connections, Product Servicing, Wrong, Chassis

Page 21

Speaker Connections

Caution: Please follow the instructions given below. Failure to do so will cause damage to the unit and speakers.

 

 

<Right>

L +

(White)

+

 

-

 

-

 

(White

 

 

w/black stripe)

 

+

(Gray)

R

+

-

-

 

 

(Gray

 

 

w/black stripe)

<Wrong>

Use ungrounded speaker only.

The maximum speaker input should be 37 W or more. (If used with the optional power amplifier, the speaker input should be higher than the maximum amplifier output.)

The speaker impedance should be 4 - 8 1.

This unit uses the BTCL circuit, so each speaker should be connected separately using parallel vinyl insulated cords.

The speaker cords and the power amplifier unit should be kept away (about 30 cm apart) from the antenna and antenna extension cord.

L

+

+

-

-

 

Chassis

+

+

R -

-

Chassis

Never connect the speaker cord to the body of the car.

L

+

+

L

+

+

+

-

-

-

-

-

 

+

+

 

+

+

+

R -

-

R -

-

-

• Do not use a 3-wire type speaker

• Do not connect more than one

system having a common earth

speaker to one set of speaker

lead.

leads.

Product Servicing

If the suggestions in the charts do not solve the problem, we recommend that you take it to your nearest authorized Panasonic Service center. The product should be serviced only by a qualified technician.

Maintenance

Your product is designed and manufactured to ensure the minimum of maintenance. Use a soft cloth for routine exterior cleaning. Never use benzine, thinner, or other solvents.

Caution

This product is designed without a fuse inside due to fuses already exist in your vehicle. We would recommend to use fuses of the specified rating (10 A). Using fuses that exceed the prescribed capacity could cause this product to start smoking, ignite or other malfunction.

If your vehicle is without the fuse or a circuit braker to protect this unit ,please your dealer add the specified fuse 10 A or a circuit breaker at the BATTERY lead of your vehicle's harness. please see page 26 to find out where "BATTERY + 12 V" is for your dealer adding the fuse or the circuit breaker.

21

CQ-5335U

Image 21
Contents CQ-5335U Following applies only in the U.S.A Safety InformationLaser Products Wave length 780 nm FCC WarningWhen Washing Your Car When DrivingUse Authorized Service centers When ParkedContents Power Power and Sound ControlsVolume LoudnessBass Illumination SwitchingTreble BalanceTime Reset Clock SettingSelecting the Clock Display Initial TimeInitial Alarm Time Alarm Time SettingAlarm Operation Alarm output Volume SelectionRadio Auto Preset Memory APM Radio Preset Station SettingManual Preset Memory Preset Station CallingWeather Band Stations Tuning in a Weather Band StationDisc Insert and Playback Disc insert CD PlayerStop and Disc Eject Listening to a CDRepeat play Random play Scan play Track Selection Track SearchCD Changer Control CD Changer modeDisc Selection Track SelectionScan Play Tracks Discs Remote ControlRepeat Play Tracks Discs Random Play Tracks DiscsTroubleshooting Preliminary StepsCommon Clean disc, referring to the section on Notes on Discs Select other stations of higher signal levelRadio Extend fully the radio antennaAdjust mounting angle to less than 30˚ Sound SettingConnect the speaker wires to the correct ones Trouble Sound skips due to vibration Disc is not ejectedCD changer Error Display MessagesCheck the disc Select the next available compact disc. Check the discMaintenance Cleaning this UnitCare of the Unit Product Servicing Speaker ConnectionsWrong ChassisDashboard Specifications Installation GuidePanasonic Servicenter List for Service Directory OverviewDashboard Installation InstallationInstallation Hardware Using the rubber cushion optionExample Mounting springs CInsert each Removal Tool i and pull Removal Tool U-shaped To Remove the Unit from the vehicles dashboardWiring Diagram Electrical ConnectionsCD Receiver Not used Specifications Memo Memo