Panasonic CQ-5335U Alarm Time Setting, Initial Alarm Time, Alarm Operation, Alarm Time Reset

Page 8

Alarm Time Setting

The 12-hour system is used for the clock.

Initial Alarm Time

Press and hold [ALM] (Alarm)

“AM 12:00” is displayed when the alarm is not adjusted.

CLK

PWR

ALM
PUSH SEL/SAT	DISP	CQ-5335U					LOUD
VOL
	MODE						MUTE
							TUNE
		DISC		CD SCAN	RPT	RDM	SEEK
	BAND	DISC		CD SCAN	RPT	RDM	SCAN
	BAND						SCAN
BASS/TREB/BAL/FADER	1	2	3	4	5	6	ILL
BASS/TREB/BAL/FADER	APM						ILL

[{ TUNE], [} TUNE]

(Hours, Minutes)

Alarm Time Setting

q Press and hold [ALM] (Alarm) and do not release to set alarm time. Display blinks and the alarm time setting mode is activated.

(blink.)

Hours

w Press [{] to set the hour.

(Hours set.)

Alarm Operation

•Alarm is switched to ON or OFF each time [ALM] is pressed.

•When the alarm is switched to ON, the alarm will sound at the set alarm time.

Turning off the Alarm Sound

The alarm will turn off automatically after 90 seconds. Otherwise, press [ALM] once.

Alarm output Volume Selection

You can select ALARM VOL 1 (or VOL 2) by pressing [ALM] in sequence and the display will show as follows.

Minutes

e Press [}] to set the minute.

(Minutes set.)

r Once the alarm time has been set, release [ALM].

Note: Press and hold [{] or [}] to change numbers rapidly.

Alarm Time Reset

When you want to reset the alarm time, repeat steps q to r.

a a OFF

Cautions:

•Be careful not to set wrong alarm time, otherwise, the alarm may sound while driving.

•If the alarm is set, be sure to check the set alarm time by pressing [CLK].

•If volume is set at “0” level, the output volume will be muted. (Even when ALARM is acting.)

8

CQ-5335U

Image 8

Contents CQ-5335U Safety Information Following applies only in the U.S.ALaser Products Wave length 780 nm FCC WarningWhen Driving When Washing Your CarUse Authorized Service centers When ParkedContents Power and Sound Controls PowerVolume LoudnessIllumination Switching BassTreble BalanceClock Setting Time ResetSelecting the Clock Display Initial TimeAlarm Time Setting Initial Alarm TimeAlarm Operation Alarm output Volume SelectionRadio Radio Preset Station Setting Auto Preset Memory APMManual Preset Memory Preset Station CallingTuning in a Weather Band Station Weather Band StationsCD Player Disc Insert and Playback Disc insertStop and Disc Eject Listening to a CDTrack Selection Track Search Repeat play Random play Scan playCD Changer mode CD Changer ControlDisc Selection Track SelectionRemote Control Scan Play Tracks DiscsRepeat Play Tracks Discs Random Play Tracks DiscsCommon TroubleshootingPreliminary Steps Select other stations of higher signal level Clean disc, referring to the section on Notes on DiscsRadio Extend fully the radio antennaSound Setting Adjust mounting angle to less than 30˚Connect the speaker wires to the correct ones Trouble Sound skips due to vibration Disc is not ejectedError Display Messages CD changerCheck the disc Select the next available compact disc. Check the discCare of the Unit MaintenanceCleaning this Unit Speaker Connections Product ServicingWrong ChassisInstallation Guide Dashboard SpecificationsPanasonic Servicenter List for Service Directory OverviewInstallation Dashboard InstallationInstallation Hardware Using the rubber cushion optionMounting springs C ExampleTo Remove the Unit from the vehicles dashboard Insert each Removal Tool i and pull Removal Tool U-shapedCD Receiver Wiring DiagramElectrical Connections Not used Specifications Memo Memo