Panasonic CQ-5335U Preparation, Dashboard Installation, Installation Hardware

Page 23

Installation (Continued)

❐Preparation

Warning: If your vehicle is equipped with air bag and/or anti-theft systems, specific procedures may be required for connection and disconnection of the battery to install this product.

Before attempting installation of this electronic component, contact your vehicle dealer or manufacturer to determine the required procedure and strictly follow their instructions.

FAILURE TO FOLLOW THE PROCEDURE MAY RESULT IN THE UNINTENDED DEPLOYMENT OF AIR BAGS OR ACTIVATION OF THE ANTI-THEFT SYSTEM RESULTING IN DAMAGE TO THE VEHICLE AND PERSONAL INJURY.

•Disconnect the cable from the negative battery terminal (see warning and caution below).

•Remove Mounting Collar q from the main unit temporarily, which are already mounted at shipment.*

Caution: Various settings that have been stored in the memory in other on-board equipment (vehicle navigation etc.) may be lost if the battery terminals are disconnected.

Therefore, we recommend to make a record of or to back up the settings before disconnecting the terminals.

After completing installation of the main unit, set the equipment again according to the record.

•Unit should be installed in a horizontal position with the front end up at a convenient angle, but not more than 30˚.

❐Dashboard Installation

Installation Opening

This unit can be installed in any dashboard having an opening as shown below. The dashboard should be 3/16” (4.75 mm) – 7/32” (5.56 mm) thick in order to be able to support the unit.

❐Installation Hardware

No.

Item

Diagram Q’ty

q Mounting Collar*

1

w Plain washer (5mmø)

2

e Spring Washer (5mmø)

2

r Hex. Nut (5mmø)

2

t Rear Support Strap

1

y

Hex. Bolt

1

(5mmø ⋅ 25 mm)

u

Toothed Lock Washer

1

(5mmø)

i

Removal Tool

2

 

(U-shaped)

 

o Antenna Connector

1

(a) Using the rear support strap t

 

(b) Using the rubber cushion (option)

Rear support bracket

Rubber cushion (option) (provided on the vehicle)

Mounting bolt (5 mmø)

q Mounting collar

23

CQ-5335U

Page 22 Page 24
Image 23
Page 22 Page 24
Contents CQ-5335U FCC Warning Safety InformationFollowing applies only in the U.S.A Laser Products Wave length 780 nmWhen Parked When DrivingWhen Washing Your Car Use Authorized Service centersContents Loudness Power and Sound ControlsPower VolumeBalance Illumination SwitchingBass TrebleInitial Time Clock SettingTime Reset Selecting the Clock DisplayAlarm output Volume Selection Alarm Time SettingInitial Alarm Time Alarm OperationRadio Preset Station Calling Radio Preset Station SettingAuto Preset Memory APM Manual Preset MemoryWeather Band Stations Tuning in a Weather Band StationListening to a CD CD PlayerDisc Insert and Playback Disc insert Stop and Disc EjectRepeat play Random play Scan play Track Selection Track SearchTrack Selection CD Changer modeCD Changer Control Disc SelectionRandom Play Tracks Discs Remote ControlScan Play Tracks Discs Repeat Play Tracks DiscsCommon TroubleshootingPreliminary Steps Extend fully the radio antenna Select other stations of higher signal levelClean disc, referring to the section on Notes on Discs RadioTrouble Sound skips due to vibration Disc is not ejected Sound SettingAdjust mounting angle to less than 30˚ Connect the speaker wires to the correct onesSelect the next available compact disc. Check the disc Error Display MessagesCD changer Check the discCare of the Unit MaintenanceCleaning this Unit Chassis Speaker ConnectionsProduct Servicing WrongOverview Installation GuideDashboard Specifications Panasonic Servicenter List for Service DirectoryUsing the rubber cushion option InstallationDashboard Installation Installation HardwareExample Mounting springs CInsert each Removal Tool i and pull Removal Tool U-shaped To Remove the Unit from the vehicles dashboardCD Receiver Wiring DiagramElectrical Connections Not used Specifications Memo Memo
Top Page Image Contents