Bosch Appliances PLE-2MA120-EU manual Controls, connectors and indicators, Front panel

Page 9

Plena Mixer Amplifier Installation and User Instructions Description

en 9

2.4Controls, connectors and indicators

2.4.1Front panel

See figure 2.2 for an overview of the controls and indicators.

1 Power button.

2Label holder for user-defined description of microphone/line inputs - custom labels can be

created by user.

3Master high tone control for microphone/line inputs.

4 Label holder for user-defined description of music sources - custom labels can be created by user.

5 Master high tone control for music inputs.

6 Label holder for user-defined description of zone

names - custom labels can be created by user.

7 Master volume control - controls all inputs except emergency and call station.

8 Output level meter (-18 db, 0 db)

9 Input level control:

microphone/line 1

microphone/line 2

microphone/line 3

microphone/line 4

microphone/line 5

microphone/line 6

10Master low tone control for microphone/line inputs.

11Music source selector (for music inputs 1, 2, and 3).

12Music source volume control.

13Master low tone control for music inputs.

14Zone 1 selection button.

15Zone 2 selection button

16 Air inlet holes.

Note

Do not obstruct the airflow into the unit.

17 Headphone socket.

Note

Users can create custom labels for the: microphone/line inputs, description of the music sources, and audio output zones 1 and 2. These labels can be attached to the mixer amplifier at position numbers 2, 4, and 6 (see figure 2.2). Colored pins can also be inserted at various positions around the dial controls to indicate the favorite settings for a particular application. For more information on inserting and removing pins, see section 4.3.2.

2.4.2Plena PLE-WP2Z3S wall panel

The optional Plena PLE-WP2Z3S wall panel can be used to remotely control the unit from a maximum of four remote locations. The appearance of the wall panel is matched to the Bosch loudspeaker volume controls.

The zone can be activated or deactivated, and the music source can be easily changed. The status of each zone and music source is indicated by an LED.

A standard CAT 5 cable is used to connect the wall panel to the mixer-amplifier. The maximum distance is 200 m. Please refer to the relevant datasheet for more information.

1

2

3

 

4

5

 

6

7

8

 

 

 

 

 

 

 

 

 

B

9

 

10

11

12

13

14

15

16

17

figure 2.2: Front panel

Bosch Security Systems 2007-10 PLE-2MA120-EU, PLE-2MA240-EU en

Image 9
Contents Plena Mixer Amplifier Important safeguards Table of contents Operation Purpose IntroductionDigital document Intended audience Related documentationConversion of units of mass Conversion tablesDescription Contents of boxPlena product range Plena Mixer AmplifierSchematic overview of the Plena Mixer Amplifier Controls, connectors and indicators Front panelPlena PLE-WP2Z3S wall panel Rear panel Rear panel Intentionally left blank Install unit in rack optional InstallationCheck settings/connections Unpack unitIntentionally left blank Connections and settings Connecting inputsDC supply battery Priority microphone input XLR connector onlyAdditional microphones inputs 3 through Secondary microphone inputEmergency inputs Connecting 100 Volt input signalConnecting emergency telephone lines Music source inputs Connecting music source inputsZone 1 Connecting outputsCall only Music onlyConstant voltage loudspeakers Connecting speakersRear panel settings Unit settingsRotary controls Pin settings and labelling Intentionally left blank Switch off Switch on and offSwitch on OperationMicrophone/line controls Music controlsTone control Master volume control Output controlsZone selection Intentionally left blank Electrical Technical dataEnvironmental MechanicalPage For more information visit