Camco 4, 2.6 manual Problem No Sound or Sound is too Low, Problem No Channel Separation

Page 24

6.0 TROUBLESHOOTING

6.3 Problem: No Sound

Indication: On LEDs not lit

Clip/Output Current Indicators not lit

Check AC plug.

Confirm that AC outlet works by plugging in another device.

Indication: On LEDs lit

Signal LEDs not lit

Make sure the signal source is operating and try another cable.

Check Position of Volume Pots.

Indication: On LEDs lit

Signal LEDs responding to signal level

Check the speaker wiring for breaks.

Try another speaker and cable.

Indication: On LED(s) sequence

The amplifier is in protective muting. Refer to On LED -

flashing sequences table to find out the cause for the mute.

Overheating will cause protective muting.

Check for proper ventilation. If the fan isn’t running the amplifier requires servicing.

6.4 Problem: No Sound or Sound is too Low

Indication: On LED not or sporadically lit

Signal LED off

Clip/Output Current indicator lit green or red

Under Impedance Limiter is active.The load impedance is abnormally low or shorted.

Unplug each speaker one-by-one. If the On LED indicates normally when

you disconnect a cable, that cable or speaker is shorted.

Take care not to use too many speakers in parallel, which would result in -

an impedance that is too low for normal operation!

Indication: On LED(s) Sequence

Please refer to the On LED sequence table to find out which protection is active.

High temperature will cause an attenuation of output level so that under

normal conditions the amp will never mute!

DC will cause the amp to mute or shut down.

Switch off the VORTEX and unplug the source from the amp’s input to prevent DC entering the amp via the signal source. Then switch on the VORTEX. If the On-indicator shows the same sequence, the amp will need to be serviced by a qualified technician.

All other LED sequences that shut down or mute the VORTEX indicate a serious internal fault. At this point, turn the VORTEX off, remove AC power and have the amplifier serviced by a qualified technician.

6.5 Problem: No Channel Separation

Check the mode indicators on the front panel.

Make sure the mode-switch on the rear panel is in the stereo-position.

Make sure other equipment in the signal path such as mixers and preamps

are set for stereo, not mono.

On the E.U.I., check the Input Signal Parallel Switch is in the stereo-

position.

P.24

CAMCO USER MANUAL

VORTEX POWER AMP SERIES

Image 24
Contents Page For Vortex Models 2.6, 4 Explanation of Symbols Please Refer ALL Servicing toSafety Replacement Parts Safety CheckServicing EC Declaration of Conformity Manufacturers NameManufacturers Address Declares that the product with the model nameContents Welcome Welcome to CamcoUnpacking Amplifier Facilities Vortex The RearInstallation On/off SwitchPrecautions MountingWiring Speakon Connection CoolingGround Lift 2 E.U.I. and XLR Connection Mode Indicators Mode SwitchStereo Operation Parallel-Mono OperationBridge-Mono Operation One-channel mono bridged operation Input Signal Chaining Controls Volume Control Limiter SwitchOperation Gain SelectorIndicators 1 On / Failure Indicators Signal IndicatorsClip / Output Current Indicators See 4.4.1,Clip Limiter and 4.4.3, Speaker Protect LimiterTo disable the Clip Limiter, see 4.2.3, Limiter Switch Power Amp Over Current Protection Power Amp Thermal ProtectionDC Servo Mains Protection Inrush Current LimitationFilter Cleaning Vortex Filter AssemblyFans See .7, Input Signal Chaining To Activate CAI Address Selection Procedure CAI Status IndicatorOverview Or Remote Controls CAI CAI allows OptionsTroubleshooting On LED Flashing Sequences Examples of LED SequencesProblem No Sound Problem No Sound or Sound is too LowProblem No Channel Separation Problem Distorted Sound Problem Music Sounds Frequency FilteredProblem Hiss Problem Squeals and FeedbackSpecification Output PowerSignal to Noise-Ratio Power Consumtion @ 230 Typical Max2Subject to technical alterations without prior notice Measurments Measurements of a typical performanceTHD+N @ 1 kHz, 4 Ohm load vs. input voltage Ch1, Ch2 Ohms Ch1, Ch2 Measurements of a typical performance Ch1, Ch2 Measurements of a typical performance1257 Vortex 2.6 Measurements of a typical performanceWarranty Information Expired Warranty Nature Of ProblemOwner’s Information Company Name Contact Shipping AddressCompany Information Mailing AddressInternet