Camco 2.6 manual THD+N @ 1 kHz, 4 Ohm load vs. input voltage Ch1, Ch2

Page 29

MEASURMENTS		300m
		200m
		100m
		50m
	Ohm	20m
		10m
		5m

8.0		2m	50	100	200	500	1k	2k	5k	10k	20k
		20	50	100	200	500	1k	2k	5k	10k	20k
						Hz
						Hz

Figure 7.5

Output impedance vs. frequency @ 1 Amp RMS injected current. (Ch1, Ch2)

equivalent 11 mOhm + 2.1uH (Measurements of a typical performance)

	-20
	-30
	-40
	-50
	-60
	-70
dB	-80
	-80
	-90
	-100
	-110
	-120	500u	1m	2m	5m	10m	20m	50m 100m 200m	500m	1	2	6
	100u 200u	500u	1m	2m	5m	10m	20m	50m 100m 200m	500m	1	2	6
						Vrms

Figure 7.6

THD+N @ 1 kHz, 4 Ohm load vs. input voltage (Ch1, Ch2)

(Measurements of a typical performance)

1000

800

factor	600
factor
Damping	400
	200

0
20	50	100	200	500	1k	2k	5k	10k	20k

Hz

Figure 7.7

VORTEX 6 damping factor into 8 Ohm

equation: damping factor= loaded impedance / amplifier output impedance

(Measurements of a typical performance)

	-20
	-30
	-40
	-50
	-60
	-70
dB	-80
	-80
	-90
	-100
	-110
	-120	50	100	200	500	1k	2k	5k	10k
	20	50	100	200	500	1k	2k	5k	10k
					Hz

Figure 7.8

THD+N vs. frequency (BW 22 kHz), 3 dB below clip, 4 ohms (Ch1, Ch2)

(Measurements of a typical performance)

P.29	CAMCO USER MANUAL
	VORTEX POWER AMP SERIES

Image 29

Contents Page For Vortex Models 2.6, 4 Please Refer ALL Servicing to Explanation of SymbolsSafety Servicing Replacement PartsSafety Check Manufacturers Name EC Declaration of ConformityManufacturers Address Declares that the product with the model nameContents Unpacking WelcomeWelcome to Camco Amplifier Vortex The Rear FacilitiesOn/off Switch InstallationPrecautions MountingGround Lift Wiring Speakon ConnectionCooling Mode Switch 2 E.U.I. and XLR Connection Mode IndicatorsBridge-Mono Operation One-channel mono bridged operation Stereo OperationParallel-Mono Operation Input Signal Chaining Limiter Switch Controls Volume ControlOperation Gain SelectorSignal Indicators Indicators 1 On / Failure IndicatorsClip / Output Current Indicators See 4.4.1,Clip Limiter and 4.4.3, Speaker Protect LimiterTo disable the Clip Limiter, see 4.2.3, Limiter Switch Power Amp Thermal Protection Power Amp Over Current ProtectionDC Servo Mains Protection Inrush Current LimitationFans Filter CleaningVortex Filter Assembly See .7, Input Signal Chaining CAI Status Indicator To Activate CAI Address Selection ProcedureOverview Or Remote Controls CAI CAI allows OptionsOn LED Flashing Sequences Examples of LED Sequences TroubleshootingProblem No Channel Separation Problem No SoundProblem No Sound or Sound is too Low Problem Music Sounds Frequency Filtered Problem Distorted SoundProblem Hiss Problem Squeals and FeedbackOutput Power SpecificationSignal to Noise-Ratio Power Consumtion @ 230 Typical Max2Subject to technical alterations without prior notice Measurements of a typical performance MeasurmentsTHD+N @ 1 kHz, 4 Ohm load vs. input voltage Ch1, Ch2 Ch1, Ch2 Measurements of a typical performance Ohms Ch1, Ch2 Measurements of a typical performanceVortex 2.6 Measurements of a typical performance 1257Warranty Information Nature Of Problem Expired WarrantyOwner’s Information Company Name Contact Shipping AddressInternet Company InformationMailing Address