Mitsubishi Electronics MDT651S 1Preparation for installation, Determine the installation location

Page 18

P-1Preparation for installation

Install the monitor on a wall or ceiling strong enough to support its weight where the screen is easy to view, using commercially available wall or ceiling mount brackets.

Determine the installation location

CAUTION:

DO NOT ATTEMPT TO INSTALL THE LCD MONITOR BY YOURSELF.

Installing your LCD monitor must be done by a qualiﬁed technician. Contact your dealer for more information.

CAUTION:

MOVING OR INSTALLING THE LCD MONITOR MUST BE DONE BY THREE OR MORE PEOPLE.

Failure to follow this caution may result in injury if the LCD monitor falls.

CAUTION:

Do not mount or operate the monitor upside down, face up, or face down.

IMPORTANT:

Lay the protective sheet, which was wrapped around the LCD monitor when it was packaged, beneath the LCD monitor so as not to scratch the panel.

Ventilation requirements for enclosure mounting

To allow heat to disperse, leave space around the monitor as shown in the ﬁgure below.

Don’t block these holes.

CAUTION:

Don’t block the holes in the rear of the monitor shown in the ﬁgure above. If they are blocked, heat accumulates inside the monitor, causing breakdown. The upper limit of the operation- guaranteed ambient temperature when the monitor is installed in the landscape position is 40˚C. When installing the monitor in a case or an enclosure, ensure adequate ventilation to keep the temperature inside the case 40˚C or lower by providing

a cooling fan or ventilation holes in the case. The upper limit when the monitor is in the portrait position is 35˚C.

This LCD has a temperature sensor and cooling fan. If the LCD becomes hot, the cooling fan will turn on automatically. If the LCD becomes overheated, the “Caution” menu will appear.

If the “Caution” menu appears, stop using the monitor and allow it to cool. When the LCD monitor is used in an enclosure or with protection on LCD surface, please check the inside temperature of the monitor by “HEAT STATUS” (See page 50). If the temperature is higher than the normal level, set “COOLING FAN” to ON using the SCREEN SAVER function (See page 46).

Downloaded From TV-Manual.com Manuals	English-14

Image 18

Contents LCD Display Monitor Page English Page Index Features Important Information Declaration of ConformityImportant Information Declaration Declaration of the ManufacturerRecommend Use ErgonomicsContents Buttons, Switch, and Indicator Parts Name and FunctionsFront Rear Control buttons Anti-theft lock slot Connectors and TerminalsParts Name and Functions VideoWireless Remote Control DescriptionHow to Use the Wireless Remote Control How to install the batteriesHow to remove the batteries CAT5 Tx BOX FrontRearGND Preparation for use Flow of preparation1Preparation for installation Determine the installation locationDo not Attempt to Install the LCD Monitor by Yourself Installing the monitor Using the monitor without the bezelLay the screen face down How to set-up 2Installing the monitorInstalling in the portrait position ConditionsBefore connecting the signal cable to PC and Video How to install the optional speakersPrevention of disconnection of Hdmi cable 4Connection procedureWiring diagram Before making connectionsAnalog connection Connection via RGB3 in D-SUB connector 4Connection procedureConnecting with a computer analog connection Second monitor connectionConnection via the RGB2 in connector DVI-D Connecting with a computer digital connectionFactory preset timing Connection via the RGB6 in connector DisplayPortConnecting a video device component video/HDMI device DVD player Component deviceVideo device Composite video/S video device Installation to Windows Vista Connecting CAT5How to install Installation to Windows XP Connection to one monitor5Connecting CAT5 Allowable cable lengthCAT5 EQ Connecting RS-232C Monitor control via RS-232C7Connecting LAN Monitor connection using LAN8Connecting the power cord to the monitor Connecting the power sourceHow to Use Flow of How to Using1Turning on all the connected devices Power Management FunctionPower Indicator Turning on external devices2Selecting the video input 3Controlling the external devices 4Selecting the OSD language5Auto-setup 6Selecting the picture mode7Screen adjustment 8Picture adjustment9Volume control 10Schedule setting10Schedule setting How to set up schedule11Remote control RS-232C/RS-485 Remote controlRemote control 11Remote control LAN Remote controlMain Menu Screen Main menu Sub menu Adjustment items Adjustment statusConﬁguration of OSD screen Operation buttons Key guideConﬁguration and basic operation of OSD screen Basic operation of OSDOSD screen functions PictureAuto Brightness Picture ResetOSD screen functions PrimaryScreen Balance Audio ResetAudio TreblePIP Picture in Picture CONFIGURATION1 CONFIGURATION2 Schedule Date and TimeMonitor Information Advanced Option Advanced Option Reset Power on DelayTerminal Setting Heat StatusOther functions Picture modeControl Lock mode Picture sizeTo control multiple monitors collectively Other functionsSupplemental information of the auto brightness function To use a computer to control the monitorsReference PIP, POP functionPIP POP Side by Side OFF Aspect Full PIP Size SmallRemote control numbering function Troubleshooting Speciﬁcations Vesa DPM Vesa DDC2B, DDC/CIPin Assignment Pin Assignment