Mitsubishi Electronics MDT651S manual Advanced Option

Page 53

OSD screen functions (continued)

ADVANCED OPTION

English

￿INPUT RESOLUTION

* For the RGB3 and RGB4 inputs only.

You can select the following resolutions according to the input signal: AUTO, 1024x768, 1280x768, 1360x768, 1366x768, 1400x1050, 1680x1050, 1600x1200, and 1920x1200. AUTO selects the resolution automatically. The setting you select becomes effective when POWER is turned OFF and ON again.

￿BLACK LEVEL EXPANSION

Selects a level of black expansion from “OFF”, “MIDDLE” and “HIGH.”

In case of go under the black cut-off level, please adjust the “Black level” in moderation on OSD menu.

￿INPUT CHANGE

You can select the time for input switching from QUICK and

NORMAL.

NOTE: When you select QUICK, slight noise may appear.

￿SCAN MODE

*For the RGB1 (HDMI), DVD/HD, VIDEO<S>, and VIDEO inputs only.

You can select the image display area.

OVERSCAN: About 95% of the input image is displayed.

UNDERSCAN: Almost 100% of the input image is displayed.

￿SCAN CONVERSION

*For the RGB1 (HDMI), DVD/HD, VIDEO<S>, and VIDEO inputs only.

You can select the IP conversion mode. PROGRESSIVE: Interlace signals are converted into

progressive signals. Select this setting for normal cases.

INTERLACE: Interlace signals are displayed without being converted. Though this setting is suitable for motion images, still images aren’t displayed properly.

￿FILM MODE

You can select the film mode function.

AUTO: Images of 24 frames per second are detected, subjected to interpolation, and then displayed.

OFF: The input video signals are displayed without being subjected to any processing.

NOTE: When FILM MODE is AUTO, set SCAN CONVERSION to PROGRESSIVE. See page 49.

￿

￿

IR CONTROL

You can lock the wireless remote control.

Select from the following two modes using the and buttons and then determine the selected mode by pressing the SET button.

NORMAL:

All the remote control operations are

 

enabled.

PRIMARY:

The first MDT651S monitor of those multi-

 

connected via RS-232C is designated as

PRIMARY.

SECONDARY: MDT651S monitors other than the first

 

one multi-connected via RS-232C are

 

designated as SECONDARY.

LOCK:

All the remote control operations are

 

disabled.

NOTE: When you hold down the DISPLAY button on the wireless remote control for at least 5 seconds, the NORMAL mode is activated.

You can lock the wireless remote control independently from the control buttons on the rear of the monitor. See page 51.

TILING

You can enlarge an image across multiple screens. A single large screen can be configured with up to 25 monitors. You can also divide the displayed image into up to 5 pieces horizontally and vertically.

NOTE: It is required to connect the same video signal to each monitor via a distributor or RGB OUT.

When TILING is activated, PIP, POP, SBS, and STILL are disabled.

TILING doesn’t work in the REAL picture size mode.

H MONITORS:

Select the number of images obtained by

 

horizontal division.

V MONITORS:

Select the number of images obtained by

 

vertical division.

POSITION:

Select the area you want to enlarge.

FRAME COMP.: When displaying an image across multiple

 

monitors, you can select the mode to

 

compensate for the bezel widths for

 

smooth and natural display.

ENABLE:

When you select ON, the image in the

 

selected area is enlarged on the screen.

Downloaded From TV-Manual.com Manuals

English-49

 

Page 52 Page 54
Image 53
Page 52 Page 54
Contents LCD Display Monitor Page English Page Index Features Declaration of Conformity Important InformationImportant Information Declaration of the Manufacturer DeclarationErgonomics Recommend UseContents Front Rear Control buttons Buttons, Switch, and IndicatorParts Name and Functions Parts Name and Functions Connectors and TerminalsAnti-theft lock slot VideoDescription Wireless Remote ControlHow to remove the batteries How to Use the Wireless Remote ControlHow to install the batteries GND CAT5 Tx BOXFrontRear Flow of preparation Preparation for useDo not Attempt to Install the LCD Monitor by Yourself 1Preparation for installationDetermine the installation location Lay the screen face down Installing the monitorUsing the monitor without the bezel Installing in the portrait position 2Installing the monitorHow to set-up ConditionsHow to install the optional speakers Before connecting the signal cable to PC and VideoWiring diagram 4Connection procedurePrevention of disconnection of Hdmi cable Before making connectionsConnecting with a computer analog connection 4Connection procedureAnalog connection Connection via RGB3 in D-SUB connector Second monitor connectionFactory preset timing Connecting with a computer digital connectionConnection via the RGB2 in connector DVI-D Connection via the RGB6 in connector DisplayPortDVD player Component device Connecting a video device component video/HDMI deviceVideo device Composite video/S video device How to install Installation to Windows XP Connecting CAT5Installation to Windows Vista Connection to one monitorCAT5 EQ 5Connecting CAT5Allowable cable length Monitor control via RS-232C Connecting RS-232CMonitor connection using LAN 7Connecting LANConnecting the power source 8Connecting the power cord to the monitorFlow of How to Using How to UsePower Indicator Power Management Function1Turning on all the connected devices Turning on external devices2Selecting the video input 4Selecting the OSD language 3Controlling the external devices6Selecting the picture mode 5Auto-setup8Picture adjustment 7Screen adjustment10Schedule setting 9Volume controlHow to set up schedule 10Schedule settingRS-232C/RS-485 Remote control 11Remote controlRemote control LAN Remote control 11Remote controlConfiguration of OSD screen Sub menu Adjustment items Adjustment statusMain Menu Screen Main menu Operation buttons Key guideBasic operation of OSD Configuration and basic operation of OSD screenPicture OSD screen functionsOSD screen functions Picture ResetAuto Brightness PrimaryScreen Audio Audio ResetBalance TreblePIP Picture in Picture CONFIGURATION1 CONFIGURATION2 Monitor Information ScheduleDate and Time Advanced Option Terminal Setting Power on DelayAdvanced Option Reset Heat StatusControl Lock mode Picture modeOther functions Picture sizeSupplemental information of the auto brightness function Other functionsTo control multiple monitors collectively To use a computer to control the monitorsPIP POP Side by Side OFF Aspect Full PIP, POP functionReference PIP Size SmallRemote control numbering function Troubleshooting Vesa DPM Vesa DDC2B, DDC/CI SpecificationsPin Assignment Pin Assignment
Top Page Image Contents