Mitsubishi Electronics LDT52IV (MT819) RS-232C command table, Power control/Input mode selection

Page 16

Controlling the Monitor with a PC (RS-232C)

RS-232C command table

How to read the command table

 

Command:

Command field (See page 12.)

 

Direction:

W When the “Parameter” is set in the parameter field (see page 12), the command functions as described

 

under “Control/Response Contents”.

 

 

R The returned value indicated under “Reply” can be obtained by setting “????”, “

?” or “???+”

 

(repeater control) in the parameter field (see page 12).

 

Parameter:

Parameter field (See page 12.)

 

Reply:

Response (Returned value)

 

*:

“A” indicates a command which can be used in power standby mode regardless of the STANDBY MODE

 

setting.

 

 

“B” indicates command which can be used in power standby mode when STANDBY MODE is set to

 

STANDARD. (It cannot be used in the power standby mode when LOW POWER is selected.)

 

“–” indicates a command which cannot be used in power standby mode.

 

Power control/Input mode selection

Function

Command

Direction

Parameter

 

Reply

Control/Response contents

*

 

 

 

 

 

 

 

 

POWER CONTROL

POWR

W

 

0

 

Switches to standby mode.

 

 

 

 

 

 

 

 

 

 

 

 

 

1

 

Returns from standby mode.

 

 

 

 

 

 

 

 

 

 

 

R

 

 

0

Standby mode

A

 

 

 

 

 

 

 

 

 

 

 

 

 

1

Normal mode

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2

Input signal waiting mode

 

 

 

 

 

 

 

 

 

INPUT MODE SELECTION

INPS

W

 

0

 

Toggle change for input mode. Terminals not selected in DVI SELECT/

 

 

 

 

 

 

 

BNC SELECT/HDMI SELECT cannot be selected.

 

 

 

 

 

 

 

 

 

 

 

 

 

1

 

PC1 DVI-D

 

 

 

 

 

 

 

“ERR” when AV1 DVI-D is selected for DVI SELECT.

 

 

 

 

 

 

 

 

 

 

 

 

 

2

 

PC3 D-SUB

 

 

 

 

 

 

 

 

 

 

 

 

 

3

 

AV3 COMPONENT

 

 

 

 

 

 

 

“ERR” when PC4 RGB is selected for BNC SELECT.

 

 

 

 

 

 

 

 

 

 

 

 

 

4

 

AV5 VIDEO

 

 

 

 

 

 

 

 

A

 

 

 

 

6

 

PC4 RGB

 

 

 

 

 

 

“ERR” when AV3 COMPONENT is selected for BNC SELECT.

 

 

 

 

 

 

 

 

 

 

 

 

 

7

 

AV1 DVI-D

 

 

 

 

 

 

 

“ERR” when PC1 DVI-D is selected for DVI SELECT.

 

 

 

 

 

 

 

 

 

 

 

 

 

8

 

AV4 S-VIDEO

 

 

 

 

 

 

 

 

 

 

 

 

 

9

 

AV2 HDMI

 

 

 

 

 

 

 

“ERR” when PC2 HDMI is selected for HDMI SELECT.

 

 

 

 

 

 

 

 

 

 

 

 

 

10

 

PC2 HDMI

 

 

 

 

 

 

 

“ERR” when AV2 HDMI is selected for HDMI SELECT.

 

 

 

 

 

 

 

 

 

 

 

R

 

 

1

PC1 DVI-D

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2

PC3 D-SUB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3

AV3 COMPONENT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

AV5 VIDEO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6

PC4 RGB

A

 

 

 

 

 

 

 

 

 

 

 

 

 

7

AV1 DVI-D

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8

AV4 S-VIDEO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

9

AV2 HDMI

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10

PC2 HDMI

 

 

 

 

 

 

 

 

 

SCREEN menu

 

Function

Command

Direction

Parameter

Reply

Control/Response contents

*

 

 

 

 

 

 

 

 

 

AUTO

 

 

ASNC

W

1

 

When the input mode is PC3, PC4.

 

 

 

 

 

 

 

 

 

 

CLOCK

 

 

CLCK

WR

0-1200

0-1200

When the input mode is PC3, PC4. Varies depending on the signal.

 

 

 

 

 

 

 

 

 

 

PHASE

 

 

PHSE

WR

0-63

0-63

When the input mode is PC3, PC4.

 

 

 

 

 

 

 

 

 

 

POSITIONING

 

POSITION OF

HPOS

WR

0-100

0-100

0-800 on PC3/PC4.

 

 

 

THE LONGEST

 

 

 

 

Varies depending on the signal.

 

 

 

DIRECTION

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

POSITION OF

VPOS

WR

0-100

0-100

0-200 on PC3/PC4.

 

 

 

THE SHORTEST

 

 

 

 

Varies depending on the signal.

 

 

 

DIRECTION

 

 

 

 

 

 

 

 

 

 

 

 

 

 

-

SIZE

 

POSITION OF

HSIZ

WR

0-100

0-100

 

 

 

 

 

 

THE LONGEST

 

 

 

 

 

 

 

 

DIRECTION

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

POSITION OF

VSIZ

WR

0-100

0-100

 

 

 

 

THE SHORTEST

 

 

 

 

 

 

 

 

DIRECTION

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RESOLUTION

 

L-DIRECTION RES

HRES

WR

300-1920

300-1920

When the input mode is PC3, PC4.

 

 

 

 

 

 

 

 

Only even numbers are valid for parameters.

 

 

 

S-DIRECTION RES

VRES

WR

200-1200

200-1200

 

 

 

 

 

 

 

 

Varies depending on the signal.

 

 

 

 

 

 

 

 

 

 

RESET

 

 

ARST

W

1

 

 

 

 

 

 

 

 

 

 

 

 

Downloaded From TV-Manual.com Manuals

E 16

Image 16
Contents Operation Guide Contents Basic Operation MuteMenu DisplayBasic Operation „Switching the screen size Wide Zoom NormalDot by Dot Cut offMenu Items Displaying the menu screen„Example of operation „Menu screen display„SETUP Menu item details„SCREEN „PICTURE„OPTION „PIP/PbyP „ENLARGE PC input„Dual screen display Power „Enlarge„SCHEDULE ENLARGE-POSAdjustments for PC screen display „Automatic adjustment„Screen display for adjustment „ADVANCED items AV input See11 E Communication procedure Controlling the Monitor with a PC RS-232CPC connection Communication conditions„Response code format 13 E„ID numbers Wait ← „Repeater control command Volume settings for all monitors are returned15 E Controlling the Monitor with a PC RS-232C „Repeater controlRS-232C command table Power control/Input mode selectionHow to read the command table Controlling the Monitor with a PC RS-232CControlling the Monitor with a PC RS-232C Picture menu 17 EAudio menu Controlling the Monitor with a PC RS-232C Setup menu Option menu19 E Image Position Epos settingHorizontal orientation Vertical orientation Controlling the Monitor with a PC RS-232C PIP/PbyP menu Initialization/Functional Restriction Setting Function menuOthers Settings to connect to a LAN Controlling the Monitor with a PC LAN21 E „ To set on the monitorDefault Gateway 0.0 This monitor is factory preset as shown below IP AddressControlling the Monitor with a PC LAN „ To set from a PC 23 E Controlling with a PCControlling the Monitor with a PC LAN „ Basic operation„ Information Standby mode, Power on is the operation available„ Control 25 E „ Network LAN Setup„ Network Security „ Network General „ Mail Originator„ Mail Recipient 27 E„ Mail Periodical URL Information „ Service & Support URL InformationSpecify the condition to display the URL M O 29 EMitsubishi Contact Information North America