Mitsubishi Electronics LDT52IV (MT819) manual Basic Operation, Mute, Menu, Display

Basic Operation

1

2

3 4

5

7	6
8

1. INPUT (Input mode selection)

The menu is displayed. Press or to select the input

mode, and press to enter.

*You can select the input terminal by pressing the input switch of the monitor.

Input mode	Video	Audio
PC1 DVI-D*1	PC1 input terminal
PC2 HDMI*2	PC2 input terminal	PC audio input
PC3 D-SUB	PC3 input terminal	terminal
PC4 RGB*3	PC4 input terminals
AV1 DVI-D*1	AV1 input terminal
AV2 HDMI*2	AV2 input terminal	AV audio input
AV3 COMPONENT*3	AV3 input terminals
		terminals
AV4 S-VIDEO	AV4 input terminal
AV5 VIDEO	AV5 input terminal

*1 Select the terminal for DVI SELECT. (See page 7.)

*2 Select the terminal for HDMI SELECT. (See page 7.) Select the terminal for HDMI AUDIO SELECT which is used for audio input. (See page 7.)

*3 Select the terminal for BNC SELECT. (See page 7.)

2. MUTE

Turns off the volume temporarily.

Press the MUTE button again to turn the sound back to the previous level.

3. MENU

Displays and turns off the menu screen (see page 5).

4. VOL +/- (Volume adjustment)

Pressing or displays the VOLUME menu when the menu screen is not displayed.

V O L U M E 15

Press or to adjust the volume of the sound.

*If you do not press any buttons for about 4 seconds, the VOLUME menu automatically disappears.

5. BRIGHT +/- (Backlight adjustment)

Pressing or displays the BRIGHT menu when the menu screen is not displayed.

	B R I G H T	15
Press	or	to adjust the brightness.

*If you do not press any buttons for about 4 seconds, the BRIGHT menu automatically disappears.

6.SIZE (Screen size selection) The menu is displayed.

Press or to select the screen size. (See page 4.)

7.DISPLAY

Displays monitor information. Every time you press this button, the display changes from INFORMATION 1 → INFORMATION 2 → display clear and so on.

INFORMATION 1		XXXX/XX/XX XXX		XX:XX:XX
INPUT MODE		:	PC3 D-SUB
SIZE		:	WIDE
COLOR MODE		:	STD
BRIGHT		:	15
VOLUME		:	15
ID No.		:	0
MODEL		:	LDT521V
S/N		:
STATUS		:	XXXX-XXXX-XXXX-XXXX
LAN
1 9 2 0 x 1 0 8 0	V: 60 Hz		H: 66.3 kHz
INFORMATION 2		XXXX/XX/XX XXX		XX:XX:XX
RS-232C/LAN SELECT :			LAN
DHCP CLIENT		:	OFF
IP ADDRESS		:	XXX.XXX.XXX.XXX
SUBNET MASK		:	XXX.XXX.XXX.XXX
DEFAULT GATEWAY :			XXX.XXX.XXX.XXX
MONITOR NAME		:	XXXXXXXXXXXX
DATA PORT		:	XXXXX
MAC ADDRESS		:	XX-XX-XX-XX-XX-XX
LAN
1 9 2 0 x 1 0 8 0	V: 60 Hz		H: 66.3 kHz

•The display disappears automatically after about 15 seconds.

•LAN is displayed during LAN communication.

•If LAN is displayed in red, there is a duplicate IP address.

8. MODE (Color mode selection)

Each time you press this button, the color mode changes in the following order:

STD (Standard) → VIVID → sRGB → STD...

•sRGB applies to PC input only.

sRGB is international standard of color representation specified by IEC (International Electrotechnical Commission). Color conversion is made in taking account of liquid crystal’s characteristics and represents color tone close to its original image.

Downloaded From TV-Manual.com Manuals 3 E