Mitsubishi Electronics LDT52IV (MT819) manual Controlling the Monitor with a PC LAN, 21 E

Page 21

Controlling the Monitor with a PC (LAN)

Your monitor can be connected to a LAN allowing you to control it from a PC on the LAN.

You can also configure the monitor to send e-mail notification when it has a problem.

The connection requires a commercially available LAN cable (UTP cable, Category 5, straight through).

Network (LAN)

LAN terminal

Hub

LAN cable (commercially available, straight)

TIPS

•You must assign an IP address to the monitor by following the procedures in “Settings to connect to a LAN”. (See the description on the right.)

•Your PC must be installed with Internet Explorer (version 6.0 or later).

•To control the monitor via LAN, set RS-232C/LAN SELECT to LAN. (See page 7.)

•You cannot use RS-232C and LAN control simultaneously.

Settings to connect to a LAN

Set the monitor’s IP address and subnet mask to match the settings of your LAN.

These settings can be made on either the monitor or a PC connected to the monitor.

The settings depend on the configuration of your LAN. Ask your LAN administrator for details.

„To set on the monitor

Set RS-232C/LAN SELECT on the SETUP menu to LAN, and then set the LAN SETUP options. (See page 7.)

After setting each item, select SET and press MENU .

DHCP CLIENT

If your LAN has a DHCP server and you wish to obtain an address automatically, change this setting to ON.

To set the address manually, set this to OFF.

IP ADDRESS

If the DHCP CLIENT is set to OFF, specify an IP address.

Press or to select items, and press or to change the values.

SUBNET MASK

If the DHCP CLIENT is set to OFF, specify the subnet mask.

Press or to select items, and press or to change the values.

DEFAULT GATEWAY

If the DHCP CLIENT is set to OFF, specify the default gateway.

If you are not using a gateway, specify “0.0.0.0”.

Press or to select items, and press or to change the values.

RESET

Resets the values of the LAN settings to the factory preset values.

Select ON and then press MENU .

Downloaded From TV-Manual.com Manuals

21 E

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Operation Guide Contents Mute Basic OperationMenu DisplayWide Zoom Normal Basic Operation „Switching the screen sizeDot by Dot Cut offDisplaying the menu screen Menu Items„Example of operation „Menu screen displayMenu item details „SETUP„SCREEN „PICTURE„OPTION „ENLARGE PC input „PIP/PbyP„Dual screen display „Enlarge Power„SCHEDULE ENLARGE-POS„Automatic adjustment Adjustments for PC screen display„Screen display for adjustment „ADVANCED items AV input See11 E Controlling the Monitor with a PC RS-232C Communication procedurePC connection Communication conditions13 E „Response code format„ID numbers Wait ← Volume settings for all monitors are returned „Repeater control command15 E Controlling the Monitor with a PC RS-232C „Repeater controlPower control/Input mode selection RS-232C command tableHow to read the command table Controlling the Monitor with a PC RS-232C17 E Controlling the Monitor with a PC RS-232C Picture menuAudio menu Option menu Controlling the Monitor with a PC RS-232C Setup menuImage Position Epos setting 19 EHorizontal orientation Vertical orientation Initialization/Functional Restriction Setting Function menu Controlling the Monitor with a PC RS-232C PIP/PbyP menuOthers Controlling the Monitor with a PC LAN Settings to connect to a LAN21 E „ To set on the monitorThis monitor is factory preset as shown below IP Address Default Gateway 0.0Controlling the Monitor with a PC LAN „ To set from a PC Controlling with a PC 23 EControlling the Monitor with a PC LAN „ Basic operationStandby mode, Power on is the operation available „ Information„ Control „ Network LAN Setup 25 E„ Network Security „ Mail Originator „ Network General27 E „ Mail Recipient„ Mail Periodical „ Service & Support URL Information URL InformationSpecify the condition to display the URL 29 E M ONorth America Mitsubishi Contact Information
Top Page Image Contents