NEC M40, M60 user manual Connection, English-32

Page 34

Controlling the LCD monitor via RS-232C Remote Control

This LCD monitor can be controlled by connecting a personal computer with a RS-232C terminal.

Functions that can be controlled by a personal computer are:

¥Power ON or OFF

¥Switching between input signals

Connection

LCD Monitor + PC

 

MULTEOS

 

 

 

MULTEOS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PC

IN

OUT

RS-232C (IN)

RS-232C (OUT)

RS-232C (IN)

(Out)

 

 

 

 

 

RS-232C Cable

RS-232C Cable

RS-232C (OUT)

MULTEOS

NOTE: If your PC (IBM or IBM compatible) is equipped only with a 25-pin serial port connector, a 25-pin serial port adapter is required. Contact your dealer for details.

*In order to function, the RS-232C OUT terminal can only be connected to another monitor of the same model. Do not connect to other types of equipment.

The following control sequence is used for a single M40/M46. To control multiple M40/M46 monitors that are daisy-chained together please use the extended control command. Instructions for the extended control command can be found on the CD included with the display. The file is called ÒExternal_control_M4X.pdfÓ. When using the following control commands, all of the daisy-chained monitors can be controlled at the same time from one monitor. Reply and status commands, however, will only pertain to the primary monitor, not secondary monitors.

1) Interface

PROTOCOL

RS-232C

BAUD RATE

9600 [bps]

DATA LENGTH

8 [bits]

 

 

PARITY BIT

NONE

 

 

STOP BIT

1 [bits]

FLOW CONTROL

NONE

 

 

This LCD monitor uses RXD, TXD and GND lines for RS-232C control.

2)Control command diagram

The command is structured by the address code, function code, data code and end code. The length of the command is different for each function.

 

Address code

Function code

Data code

 

End code

 

HEX

30h 30h

Function

Data

 

0Dh

 

 

 

 

 

 

 

 

ASCII

'0' '0'

Function

Data

 

 

 

 

 

 

 

 

 

 

[Address code]

30h 30h (ASCII code, '0' '0'), fixed.

 

[Function code]

A code of each fixed control move.

 

[Data code]

A code of each fixed control data (number) and not always indicated.

 

[End code]

0Dh (In ASCII code, '

') fixed.

English-32

Image 34
Contents M40/M46 Index TV TunnerFCC Information Canadian Department of Communications Compliance StatementEnglish-1 Disposing of your old NEC product Important InformationDeclaration Declaration of the ManufacturerSafety Precautions, Maintenance & Recommended Use Contents Parts Name and Functions Control PanelTerminal Panel Wireless Remote Control Operating Range for the Remote Control Handling the remote controlInstallation Stand Removal Attaching Mounting AccessoriesAttach Mounting Accessories English-10Prevent Tipping Main Power Switch CoverVentilation Requirements English-11Install the remote control batteries SetupDetermine the installation location Connect the supplied power cordAdjust the screen See pages 24 Switch on the power of all the attached external equipmentAdjust the sound Adjust the image SeeBefore making connections Connecting a Personal ComputerConnections Connect the LCD Monitor to a Personal ComputerConnect the LCD Monitor to Macintosh Connecting to a Macintosh ComputerEnglish-15 Connect the LCD Monitor to a Computer with a Digital Output Connecting with Digital Interface EquipmentEnglish-16 English-17 Connecting a DVD Player with component outConnect the LCD Monitor to a DVD Player RCAEnglish-18 Connecting a DVD Player with Hdmi outConnecting a DVD Player with Scart out ScartConnect the LCD Monitor to a Stereo Amplifier Connecting to a Stereo AmplifierEnglish-19 VHF300-Ohm antenna / UHF antenna Connecting to a TVPrecautions when connecting the antenna English-20Basic Operation Power on and OFF ModesEnglish-21 Picture Mode Power IndicatorUsing Power Management Information OSMOSM On-Screen-Manager Controls English-23English-24 English-25 English-26 English-27 English-28 Schedule Setting English-29Recommendations Image Sticking of LCD PanelEnglish-30 English-31 Connect PC and M40/M46Connection English-32English-33 Features English-34Troubleshooting Product Specifications Specifications M40English-36 Specifications M46 English-37Pin Assignment English-38Energy Saving Manufacturer’s Recycling and Energy InformationWeee Mark European Directive 2002/96/EC
Related manuals
Manual 68 pages 59.89 Kb