Dakota Digital 3 Performance Menu Setup, Nighttime DIM Setup, Exit fuel setup Done

Page 25

Exit fuel setup (DONE)

This will allow you to exit the fuel setup and go on to the next setup menu.

∙When “SET DONE” is displayed press and hold SW1 until you get “ - DONE ”

∙Release the switch to go onto the next menu

PERFORMANCE MENU SETUP

The performance menus can be turned on or off, allowing you scroll thought the message screens quicker if desired. Since some people don’t care for these readings, you may shut them off so they are not displayed in normal operation. All of the performance functions are displayed from information that is already wired to the control box, so disabling will not save any wiring steps.

∙Press and hold SW 1 while turning the key on.

∙Release the switch and then press and release SW1 to get to the “PERF” setup menu.

∙Press and hold the switch until “-” “PERF” is displayed to enter the setup menu, then release SW1.

∙Now you can press and release the switch to toggle from “ON”(allowing the performance

∙readings to be shown), or “OFF”(disabling, hiding the performance readings).

∙When the desired option is displayed; press and hold SW1 until you get “ - DONE ”

∙Release the switch to go onto the next menu

NOTE: In normal operation you have to use switch 1 (SW1) to reset the various performance timers. A press and hold will zero the current reading, if it can be reset.

NIGHTTIME DIM SETUP

The nighttime dim menu, “NIGHT”, allows you to set the brightness level that the dash will dim down to when the DIM terminal has power applied to it.

If you are using the separately purchased DIM-1kitfrom Dakota Digital, this brightness level doesn’t matter as you have total control of the brightness level with the twist of a knob. Using the ADJ SND and ADJ – terminals, this setting will be overridden by the DIM-1knob.

∙Press and hold SW 1 while turning the key on.

∙Release the switch and then press and release SW1 to get to the “NIGHT” setup menu.

∙Press and hold the switch until “-” “NIGHT” is displayed to enter the setup menu, then release SW1.

∙Now you can press and release the switch to gradually dim the displays (you can press

∙and hold SW1 and the displays will cycle from bright to dim)

∙When the desired brightness level is achieved, press and release SW 2 to save the brightness level and go on to the next setup menu.

25

MAN 650066:D

Page 24 Page 26
Image 25
Page 24 Page 26
Contents NOW with Solid State Sensor Technology SeriesTypical Display Setups Mounting Systems with Displays Mounted to Aluminum Mounting Universal Display Systems with SubpanelsMounting Single Lens Systems Complete Systems mounted in new bezel Mounting Kits Into Original DashesGauge System Features Description Message DisplaysControl BOX Mounting Wiring the control box into the vehicleStatus LED Terminal DescriptionsGround Tach PowerWarn DIMSPD SND SPD +SPD SPD OUTADJ SND SW 1 or Speed switchADJ WTR SNDOIL + WTROIL SND OILFuel Fuel SNDCruise Wait +Brake Right +AUX. I/O Check ENGDisplay Ribbon Cable Setting up the control box Speed sensor setup Sender Speedometer SETUP/CALIBRATIONMAN 650066D Exit setup Done Tachometer SetupEngine cylinder setup T-CAL Speed Output OutputDisplay update setup Update Volt SetupRpm warning setup Warn Tach signal setup SignalTemp sensor setup Sender Water Temp SetupTemp warning setup Warn Exit water temp setup Done OIL Pressure SetupOil pressure warning setup Warn Temp sensor test TestExit oil pressure setup Done Fuel SetupOil pressure sensor test Test Fuel sensor setup Sender Nighttime DIM Setup Performance Menu SetupExit fuel setup Done Odometer Preset Menu BUS Interface Module SetupInformation Menu Troubleshooting Guide MAN 650066D MAN 650066D Clock Instructions For VFD systems with a clock built Troubleshooting guide Service and Repair
Top Page Image Contents