Dakota Digital 3 Water Temp Setup, Temp sensor setup Sender, Temp warning setup Warn

Page 21

WATER TEMP SETUP

The water temp setup allows you select the units the temperature is displayed in, Fahrenheit or Celsius. It also allows you to set a high temperature warning point that will cause the display to flash whenever the reading on the display is higher than the set point. There is also a test mode that will display the resistance for the sensor for trouble shooting assistance.

Press and hold SW 1 while turning the key on.

Release the switch and then press and release SW1 to get to the “WATER” setup menu.

Press and hold the switch until -WATER” is displayed to enter the water setup menus, then release SW1.

Now you can press and release the switch to scroll through the water sub-menus,SENDER

WARN” “TEST” “DONE”.

When you get to the desired sub-menu press and hold the switch to select it.

Temp sensor setup (SENDER)

This menu is used to set the temp sensor type. Dakota Digital only offers one temp sensor for this system, it is SEN-04-5, 100-300 F(40-150 C), 1/8” NPT threads. You can use bushings to adapt the sensor to various locations. You will select “DD F” to read in Fahrenheit, or select “DD C” to read in Celsius.

You can also read the temp with the use of a future bus interface module (BIM). Dakota Digital offers BIM that will allow you to read the engine temp signal from an ECU if you are installing the system in a vehicle equipped with the OBDII port or a drive train from a newer vehicle, most 1996 and newer vehicles have this. You will select “BUS F” to read in Fahrenheit, or select “BUS C” to read in Celsius.

When “SENDER” is displayed press and hold SW1 until you get “ -

Release SW1 and the current sensor selection will be displayed

Press and release SW1 to scroll through the sensor options “DD FDD CBUS F” “BUS C

When the desired setting is displayed press and hold SW1 until “ - ” “ DONE” is displayed

Release the switch to go onto the next sub- menu item.

Temp warning setup (WARN)

This menu will allow you to select the high temperature warning point. When the display value is higher than this point, the WATER display will flash. The value is adjustable from 150 – 300 F (65-148 C).

When “WARN” is displayed press and hold SW1 until you get “ -

Release SW1 and the current warning point will be displayed

Press and release SW1 to increase the value from “H 150F” – “H 300F

When the desired value is displayed, press and hold SW1 until “ - ” “ DONE” is displayed

Release the switch to go onto the next sub-menu item.

21

MAN 650066:D

Image 21
Contents NOW with Solid State Sensor Technology SeriesTypical Display Setups Mounting Universal Display Systems with Subpanels Mounting Systems with Displays Mounted to AluminumMounting Single Lens Systems Complete Systems mounted in new bezel Mounting Kits Into Original DashesGauge System Features Description Message DisplaysControl BOX Mounting Wiring the control box into the vehicleTerminal Descriptions Status LEDGround Tach PowerWarn DIMSPD SND SPD +SPD SPD OUTADJ SND SW 1 or Speed switchADJ WTR SNDOIL + WTROIL SND OILFuel Fuel SNDCruise Wait +Brake Right +Check ENG AUX. I/ODisplay Ribbon Cable Setting up the control box Speed sensor setup Sender Speedometer SETUP/CALIBRATIONMAN 650066D Exit setup Done Tachometer SetupEngine cylinder setup T-CAL Speed Output OutputDisplay update setup Update Volt SetupRpm warning setup Warn Tach signal setup SignalWater Temp Setup Temp sensor setup SenderTemp warning setup Warn Exit water temp setup Done OIL Pressure SetupOil pressure warning setup Warn Temp sensor test TestFuel Setup Exit oil pressure setup DoneOil pressure sensor test Test Fuel sensor setup Sender Performance Menu Setup Nighttime DIM SetupExit fuel setup Done BUS Interface Module Setup Odometer Preset MenuInformation Menu Troubleshooting Guide MAN 650066D MAN 650066D Clock Instructions For VFD systems with a clock built Troubleshooting guide Service and Repair