Select Advanced Setup LAN Setup | NETGEAR (LG2200D) specification

U.S. Cellular® 4G LTE™ Router (LG2200D)

4.Select ADVANCED > Setup > LAN Setup.

5.In the IP Address field, type the IP address.

6.In the IP Subnet Mask, type the subnet mask of the router.

The IP address and subnet mask identifies which addresses are local to a specific device and which must be reached through a gateway or router.

7.Change the RIP settings.

Router Information Protocol (RIP) allows a router to exchange routing information with other routers.

a.In the RIP Direction list, select one of the following:

-Both. The router broadcasts its routing table periodically and incorporates information that it receives.

-Out Only. The router broadcasts its routing table periodically.

-In Only. The router incorporates the RIP information that it receives.

b.In the RIP Version list, select one of the following:

-Disabled. This is the default setting.

-RIP-1. This format is universally supported. It is adequate for most networks, unless you have an unusual network setup.

-RIP-2. This format carries more information. Both RIP-2B and RIP-2M send the routing data in RIP-2 format. RIP-2B uses subnet broadcasting. RIP-2M uses multicasting.

8.Click the Apply button. Your changes are saved.

If you changed the LAN IP address of the router, you are disconnected when this change takes effect.

9.To reconnect, close your browser, relaunch it, and log in to the router

Specify Network Settings

47

Image 47

NETGEAR (LG2200D) user manual Select Advanced Setup LAN Setup

Contents

Cellular 4G LTE Router LG2200D Compliance SupportTrademarks Contents Specify Network Settings Appendix a Supplemental Information Technical Specifications Hardware Setup Unpack Your Router Check the package contents Front Panel Signal Power Internet LAN USB WAN WiFi WPS Quality Cellular 4G LTE Router LG2200D LED and button descriptions Rear Panel  To attach the antennas Attach the AntennasFind the Best Spot for Your Router  To position your router  To seat a SIM card Seat a SIM Card Connect to the Network Access the Router  To use WPS to connect to the WiFi network Wired ConnectionWiFi Connection  To find and select the WiFi network  To log in to the router Types of LoginsUse an Internet Browser to Access the Router Label Specify Your Internet Settings Select Advanced Setup Wizard Use the Internet Setup Wizard To use the Setup Wizard Roaming automatically Specify Mobile Broadband Internet Settings To view or change the settings Select Mobile Internet Select Advanced Advanced Setup SIM Settings SIM Card PIN Code Settings To enable or disable the SIM card PIN code  To change the SIM card PIN code Control Access to the Internet Select Parental Controls  To set up Live Parental ControlsParental Controls Control Access to the Internet Click the Take me to the status screen button  To set up keyword blockingUse Keywords to Block Internet Sites  To delete keywords from the list Select Advanced Security Block Sites Select Advanced Security Block Services Block Services from the Internet To block services Control Access to the Internet Select Advanced Security Schedule Schedule When to Block Internet Sites and Services To schedule blocking  To specify a trusted computer Set Up Security Event Email Notifications To set up email notifications Avoid Blocking on a Trusted Computer Control Access to the Internet Port Forwarding to Permit External Host Communications  To forward specific incoming protocols Set Up Port Forwarding to a Local Server Click the Add Custom Service button Add a Custom Port Forwarding Service To add a custom service  To delete a port forwarding entry Edit a Port Forwarding EntryDelete a Port Forwarding Entry  To edit a port forwarding entry  To make a local web server public Application Example Make a Local Web Server PublicHow the Router Implements the Port Forwarding Rule  To add a port triggering service Set Up Port TriggeringAdd a Port Triggering Service  To enable port triggering Enable Port Triggering Application Example Port Triggering for Internet Relay Chat Clear the Disable Port Triggering check box Control Access to the Internet Specify Network Settings Select Advanced Setup WAN Setup View WAN Settings To view the WAN settings Change the MTU Size  To change the MTU size Set Up a Default DMZ Server  To change the router’s device name  To set up a default DMZ serverChange the Router’s Device Name LAN IP address Change the LAN TCP/IP SettingsSelect Advanced Setup LAN Setup  To change the LAN TCP/IP settings Select Advanced Setup LAN Setup Specify the IP Addresses that the Router Assigns Reserve LAN IP Addresses Disable the Dhcp Server Feature in the Router To disable the Dhcp server feature in the router  To delete a reserved address entry  To reserve an IP address To edit a reserved address entry Select Advanced Setup QoS Setup Quality of Service SetupWMM QoS for Wireless Multimedia Applications  To disable WMM QoS  To create a QoS policy for applications and online games Set Up QoS for Internet AccessSelect the Turn Internet Access QoS On check box Specify Network Settings Click the Add Priority Rule button QoS for a Router LAN Port Click Add Priority Rule QoS for a MAC Address  To delete a QoS policy Select Advanced QoS Setup To edit a QoS policy Select Advanced WPS Wizard Use the WPS Wizard for WiFi ConnectionsSpecify Basic WiFi Settings  To use the WPS Wizard  To specify basic wireless settings  To change the WPA settings Change the WiFi Security Option Enable or Disable the Wireless Radios Control the Wireless RadiosUse the WiFi On/Off Button  To set up the wireless schedule Set Up a Wireless Schedule To enable or disable the wireless radios Select Advanced Advanced Setup WiFi Settings  To specify WPS Settings Specify WPS Settings Set Up a Wireless Distribution System Following figure shows a wireless repeating scenario  To set up the base station Set Up the Base Station  To configure a Netgear router as a repeater Set Up a Repeater Specify Network Settings USB Storage  To map the USB device to a Windows network drive Access a USB Storage Device To connect a USB storage device  To access the USB drive with FTP from a remote computer  To access the USB drive from a remote computer  To share files with your friends and family File-Sharing ScenariosShare Photos Store Files in a Central Location for Printing  To view basic information about the USB storage device View a USB Device Attached to the RouterShare Large Files over the Internet Select Basic ReadySHARE USB Storage Device Network and Access Settings To view or change the USB storage advanced settings Network Neighborhood/MacShare. Enabled by default Select Advanced USB Storage Advanced Settings  To view network folders Available Network Folders  To edit a network folder  To add a network folderSelect Advanced ReadySHARE Click the Create Network Folder button Specify Approved USB Devices  To set up approved USB devices  To remove a USB disk drive safely Select USB Storage Basic SettingsSafely Remove a USB Drive Select the Allow only approved devices check box ReadySHARE Printer ReadySHARE Printer  To set up ReadySHARE Printer ReadySHARE Printer ReadySHARE Printer ReadySHARE Printer Netgear USB Control Center utility USB Control Center Utility USB Printer Control Center Configuration Printers and Faxes screen Scan with a Multifunction Printer Administration Select Advanced Administration Router Update Update the Router Firmware To check for new firmware and update your router Select Advanced Administration LTE Modem Upgrade LTE Modem Upgrade To upgrade the LTE modem software Select Advanced Administration Set Password Change the admin Password To set the admin password  To recover your password Recover the admin Password To set up password recovery  To view router status and usage information Reboot the Router To reboot the router View Router Status Modem Identity Select Advanced Administration Router Status Gateway IP Address LAN Port IP Subnet Mask Wireless PortView Mobile Broadband Status Connection Status Select Advanced  To view statistics for the Internet connection Show Statistics Select Attached Devices View Devices Currently on the Network To view the Attached Devices screen  To view logs Select Advanced Administration LogsView Logs of Router Activity Select Advanced Administration Backup Settings Manage the Configuration FileBack Up the Configuration Settings  To back up the router’s configuration settings Do not interrupt the reboot process Restore Configuration SettingsErase the Current Configuration Settings  To restore configuration settings that you backed up Static Routes  To set up a static routeSelect Advanced Advanced Setup Static Routes  To edit a static route  To delete a static route  To set up remote managementRemote Management Administration 104 Universal Plug and Play  To specify Universal Plug and Play settings  To monitor Internet traffic Monitor Internet Traffic Click Advanced Advanced Setup Traffic Meter Select Advanced Administration Diagnostics Diagnostics To run the diagnostics Administration 109 Troubleshooting LEDs Never Turn Off Power LED Is Off or BlinkingPower LED Stays Amber Troubleshoot with the LEDs Internet LED Is Off WiFi LED Is OffCannot Log In to the Router Forgotten WiFi Password Problems with Date and Time  To ping the router from a Windows computer WiFi ConnectivityTroubleshoot Your Network Using the Ping Utility Test the LAN Path to Your Router Test the Path from Your Computer to a Remote Device Set Up an Ethernet WAN Internet Connection Cable a WAN Ethernet Internet Connection  To install the router with an Ethernet Internet connection  To change the Internet setup Specify the Internet Connection ModeAdvanced Internet Setup Select Advanced Setup Broadband Settings Select Advanced Setup Internet Setup Internet IP Address Internet Service Provider. PPPoE or PPPoA Requirements for Entering IPv6 Addresses  To set up an IPv6 Internet connection typeSelect Advanced Advanced Setup IPv6 IPv6 Auto Detect IPv6 Auto Config IPv6 6to4 Tunnel Set Up an Ethernet WAN Internet Connection 125 IPv6 Fixed  To set up a pass-through IPv6 Internet connection To set up a fixed IPv6 Internet connection IPv6 Pass Through Set Up an Ethernet WAN Internet Connection 127 IPv6 Dhcp  To set up an IPv6 Internet connection with a Dhcp server IPv6 PPPoE  To set up a PPPoE IPv6 Internet connection Connect to the Internet Troubleshoot an Ethernet WAN Internet Connection Troubleshoot Internet Browsing Supplemental Information Factory default settings Factory Settings Supplemental Information 134 LG2200D Router specifications Technical Specifications