NETGEAR (LG2200D) guide

U.S. Cellular® 4G LTE™ Router (LG2200D)

The following figure shows a wireless repeating scenario.

Repeater

Base stationaccess point access point

Figure 5. Wireless repeating scenario

You must set up a wireless base station and a wireless repeater:

•Wireless base station. The router acts as the parent access point that bridges traffic to and from the child repeater access point. The base station also handles wireless and wired local computers. To configure this mode, you must know the MAC addresses of the child repeater access point. Often, the MAC address is on the product label.

•Wireless repeater. The router sends all traffic from its local wireless or wired computers to a remote access point. To configure this mode, you must know the MAC address of the remote parent access point.

The router is always in dual-band concurrent mode, unless you turn off one radio. If you enable the wireless repeater in either radio band, the wireless base station or wireless repeater cannot be enabled in the other radio band. However, if you enable the wireless base station in either radio band and use the other radio band as a wireless router or wireless base station, dual-band concurrent mode is not affected.

Before you an set up a wireless network with WDS, both access points must meet the following conditions:

•Use the same SSID, wireless channel, and encryption mode.

•Be on the same LAN IP subnet. That is, all of the access point LAN IP addresses are in the same network.

•All LAN devices (wired and wireless computers) are configured to operate in the same LAN network address range as the access points.

Specify Network Settings

64

Image 64

NETGEAR (LG2200D) user manual Following figure shows a wireless repeating scenario

Contents

Cellular 4G LTE Router LG2200D Trademarks SupportCompliance Contents Specify Network Settings Appendix a Supplemental Information Technical Specifications Hardware Setup Check the package contents Unpack Your Router Signal Power Internet LAN USB WAN WiFi WPS Quality Front Panel Rear Panel Cellular 4G LTE Router LG2200D LED and button descriptions Find the Best Spot for Your Router Attach the Antennas To attach the antennas  To position your router Seat a SIM Card  To seat a SIM card Connect to the Network Access the Router Wired Connection WiFi Connection To find and select the WiFi network  To use WPS to connect to the WiFi network Types of Logins Use an Internet Browser to Access the RouterLabel  To log in to the router Specify Your Internet Settings  To use the Setup Wizard Use the Internet Setup WizardSelect Advanced Setup Wizard Specify Mobile Broadband Internet Settings  To view or change the settingsSelect Mobile Internet Roaming automatically  To enable or disable the SIM card PIN code SIM Card PIN Code SettingsSelect Advanced Advanced Setup SIM Settings  To change the SIM card PIN code Control Access to the Internet Parental Controls  To set up Live Parental ControlsSelect Parental Controls Control Access to the Internet Use Keywords to Block Internet Sites  To set up keyword blockingClick the Take me to the status screen button Select Advanced Security Block Sites  To delete keywords from the list  To block services Block Services from the InternetSelect Advanced Security Block Services Control Access to the Internet  To schedule blocking Schedule When to Block Internet Sites and ServicesSelect Advanced Security Schedule Set Up Security Event Email Notifications  To set up email notificationsAvoid Blocking on a Trusted Computer  To specify a trusted computer Control Access to the Internet Port Forwarding to Permit External Host Communications Set Up Port Forwarding to a Local Server  To forward specific incoming protocols  To add a custom service Add a Custom Port Forwarding ServiceClick the Add Custom Service button Edit a Port Forwarding Entry Delete a Port Forwarding Entry To edit a port forwarding entry  To delete a port forwarding entry How the Router Implements the Port Forwarding Rule Application Example Make a Local Web Server Public To make a local web server public Add a Port Triggering Service Set Up Port Triggering To add a port triggering service Enable Port Triggering  To enable port triggering Clear the Disable Port Triggering check box Application Example Port Triggering for Internet Relay Chat Control Access to the Internet Specify Network Settings  To view the WAN settings View WAN SettingsSelect Advanced Setup WAN Setup Change the MTU Size Set Up a Default DMZ Server  To change the MTU size Change the Router’s Device Name  To set up a default DMZ server To change the router’s device name Change the LAN TCP/IP Settings Select Advanced Setup LAN Setup To change the LAN TCP/IP settings LAN IP address Select Advanced Setup LAN Setup Specify the IP Addresses that the Router Assigns  To disable the Dhcp server feature in the router Disable the Dhcp Server Feature in the RouterReserve LAN IP Addresses  To edit a reserved address entry  To reserve an IP address To delete a reserved address entry Quality of Service Setup WMM QoS for Wireless Multimedia Applications To disable WMM QoS Select Advanced Setup QoS Setup Select the Turn Internet Access QoS On check box Set Up QoS for Internet Access To create a QoS policy for applications and online games Specify Network Settings QoS for a Router LAN Port Click the Add Priority Rule button QoS for a MAC Address Click Add Priority Rule  To edit a QoS policy Select Advanced QoS Setup To delete a QoS policy Use the WPS Wizard for WiFi Connections Specify Basic WiFi Settings To use the WPS Wizard Select Advanced WPS Wizard  To specify basic wireless settings Change the WiFi Security Option  To change the WPA settings Use the WiFi On/Off Button Control the Wireless RadiosEnable or Disable the Wireless Radios Set Up a Wireless Schedule  To enable or disable the wireless radiosSelect Advanced Advanced Setup WiFi Settings  To set up the wireless schedule Specify WPS Settings  To specify WPS Settings Set Up a Wireless Distribution System Following figure shows a wireless repeating scenario Set Up the Base Station  To set up the base station Set Up a Repeater  To configure a Netgear router as a repeater Specify Network Settings USB Storage  To connect a USB storage device Access a USB Storage Device To map the USB device to a Windows network drive  To access the USB drive from a remote computer  To access the USB drive with FTP from a remote computer File-Sharing Scenarios Share PhotosStore Files in a Central Location for Printing  To share files with your friends and family Share Large Files over the Internet View a USB Device Attached to the Router To view basic information about the USB storage device  To view or change the USB storage advanced settings USB Storage Device Network and Access SettingsSelect Basic ReadySHARE Select Advanced USB Storage Advanced Settings Network Neighborhood/MacShare. Enabled by default Available Network Folders  To view network folders  To add a network folder Select Advanced ReadySHAREClick the Create Network Folder button  To edit a network folder  To set up approved USB devices Specify Approved USB Devices Select USB Storage Basic Settings Safely Remove a USB DriveSelect the Allow only approved devices check box  To remove a USB disk drive safely ReadySHARE Printer  To set up ReadySHARE Printer ReadySHARE Printer ReadySHARE Printer ReadySHARE Printer ReadySHARE Printer USB Control Center Utility Netgear USB Control Center utility Control Center Configuration USB Printer Scan with a Multifunction Printer Printers and Faxes screen Administration  To check for new firmware and update your router Update the Router FirmwareSelect Advanced Administration Router Update  To upgrade the LTE modem software LTE Modem UpgradeSelect Advanced Administration LTE Modem Upgrade  To set the admin password Change the admin PasswordSelect Advanced Administration Set Password  To set up password recovery Recover the admin Password To recover your password Reboot the Router  To reboot the routerView Router Status  To view router status and usage information Select Advanced Administration Router Status Modem Identity IP Subnet Mask Wireless Port View Mobile Broadband StatusConnection Status Gateway IP Address LAN Port Select Advanced Show Statistics  To view statistics for the Internet connection  To view the Attached Devices screen View Devices Currently on the NetworkSelect Attached Devices View Logs of Router Activity Select Advanced Administration Logs To view logs Manage the Configuration File Back Up the Configuration Settings To back up the router’s configuration settings Select Advanced Administration Backup Settings Restore Configuration Settings Erase the Current Configuration Settings To restore configuration settings that you backed up Do not interrupt the reboot process Select Advanced Advanced Setup Static Routes  To set up a static routeStatic Routes  To edit a static route Remote Management  To set up remote management To delete a static route Administration 104  To specify Universal Plug and Play settings Universal Plug and Play Monitor Internet Traffic  To monitor Internet traffic Click Advanced Advanced Setup Traffic Meter  To run the diagnostics DiagnosticsSelect Advanced Administration Diagnostics Administration 109 Troubleshooting Power LED Is Off or Blinking Power LED Stays AmberTroubleshoot with the LEDs LEDs Never Turn Off Cannot Log In to the Router WiFi LED Is OffInternet LED Is Off Problems with Date and Time Forgotten WiFi Password WiFi Connectivity Troubleshoot Your Network Using the Ping UtilityTest the LAN Path to Your Router  To ping the router from a Windows computer Test the Path from Your Computer to a Remote Device Set Up an Ethernet WAN Internet Connection  To install the router with an Ethernet Internet connection Cable a WAN Ethernet Internet Connection Specify the Internet Connection Mode Advanced Internet SetupSelect Advanced Setup Broadband Settings  To change the Internet setup Select Advanced Setup Internet Setup Internet Service Provider. PPPoE or PPPoA Internet IP Address  To set up an IPv6 Internet connection type Select Advanced Advanced Setup IPv6IPv6 Requirements for Entering IPv6 Addresses Auto Detect IPv6 Auto Config IPv6 6to4 Tunnel Set Up an Ethernet WAN Internet Connection 125  To set up a pass-through IPv6 Internet connection  To set up a fixed IPv6 Internet connectionIPv6 Pass Through IPv6 Fixed Set Up an Ethernet WAN Internet Connection 127  To set up an IPv6 Internet connection with a Dhcp server IPv6 Dhcp  To set up a PPPoE IPv6 Internet connection IPv6 PPPoE Troubleshoot an Ethernet WAN Internet Connection Connect to the Internet Troubleshoot Internet Browsing Supplemental Information Factory Settings Factory default settings Supplemental Information 134 Technical Specifications LG2200D Router specifications