Sanus Systems LA112 Calibrate the Arm, Calibrate Arm to the Monitor, Adjust Monitor Position

Page 15

9: Calibrate the Arm

Calibrate Arm to the Monitor

NOTE: LA112 must be calibrated to the TV to avoid hitting the wall.

1. Turn the control box power switch to “Off”.

2. While holding down the “Set” button, turn the control box power switch back on and continue to hold Set until “Ct” appears in the LED display.

3. Stand away from the LA112 as it calibrates. LA112 will move back to the home position against the wall when calibration is complete.

4. If your TV is not parallel with the wall, proceed to the next section,“Reset the LA112 to Home Position”.

Reset the LA112 Home Position

1. Move the X-arm to its home position against the wall by pressing the “SEL-IN/OUT”button on the remote control.

2. Insert the pointer into the control box Selector hole and press the “SET” button until the display reads “HP”.

3. Adjust the X-arm to the desired home position using the arrow keys on the remote control.

4. Press and hold the control box “Set” button for three seconds. Now the X-arm will move to the new home position each time the “SEL-IN/OUT”button on the remote control is pushed.

Adjust Monitor Position

CAUTION

Avoid property damage and personal injury. Set the correct width for your TV before using the LA112. See the “Setting LA112 TV Width” section above to set the correct width for your TV. While the LA112 is in motion keep people and objects away from it and do not leave it unattended.

1. Turn the control box power switch to “On”.

2. Press the “X-arm”and the the “Power” keys on the remote control.

3. If the TV width code is not displayed on the control box, press “POWER” on the remote. Then press “SEL-IN/OUT”once to extend the TV out from the wall. There is no need to hold down the button. Pressing any of the arrow buttons while LA112 is moving the TV will stop it.

4. Use the remote control arrow keys to move the TV in the desired direction. To stop movement, press any of the arrow keys or the “SEL-IN/OUT”key.

6901-100189 <01>

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Backed by CLO LA112Supplied Parts and Hardware Measure width between holesMeasure height between holes 14 x 01 x 02 x 04 x05 x 06 x 07 x 10 x 11 x 12 x 08 x6901-100189 Remove Wall Plate from Arm Remove Mounting Brackets Mount Wall Plate For Wood Stud WallsMin .5 cm 2.5 For Concrete Block or Brick Walls Install Arm Assembly to Wall Plate Selector Set Set the Monitor WidthInstall Mounting Brackets Top18, 19 12, 13, 14, 15, 16 21, 22 Route Cables For Power Outlets Located Outside the BellowsFor Power Outlets Located Inside the Bellows Install Monitor to Wall Plate Calibrate Arm to the Monitor Reset the LA112 Home PositionAdjust Monitor Position Calibrate the ArmCBL mode Page Up Using the Remote ControlPress Programming the Preset Position KeysProgramming the Remote to Operate an Existing TV Programming Codes TV Programming CodesTV Brand Code Numbers RCA NECSSS TMKKLH DVD Programming CodesDVD Brand Code Numbers JVCVCR Brand Code Numbers VCR Programming CodesSTS TeacBrand Code Numbers For Cable BoxesA1,A2, or A3 is displayed on control box TroubleshootingHow to Correct Arm Will Not MoveC1,C2,C3 or C4 is displayed on control box Power Switch Control Box LED Display Selector Set ButtonHC is displayed on control box H1,H2, or H3 is displayed on control box If Your TV Leans Forward at the Home Position MaintenanceHome Automation Controls To register by mail WarrantyPurchaser Information Product Information
Top Page Image Contents