Blaupunkt RCM 126 operating instructions Receiving traffic programme stations with RDS-EON, On/off

Page 18

Receiving traffic programme stations with RDS-EON

The abbreviation “EON” stands for Enhan- Traffic announcement priority

ced Other Networks, meaning the exchan-

on/off

ge of information within a radio network.

If the priority for traffic announcement pro-

Many FM broadcasters offer traffic messa-

grammes is activated, “TA” will light up in

ges for their service area at regular inter-

the display.

vals.

To switch the priority on or off:

All traffic programme stations transmit a

• Press the TA button.

special carrier signal alongside their pro-

When pressing TA while a message is being

grammes, which is decoded by your car ra-

broadcast, this message will be interrupted.

dio. If this signal is identified, “TP” will ap-

pear in the display (Traffic Programme).

The unit will then switch back to the pre-

In addition to these, there are also stations

vious condition. The priority for other traffic

messages remains active.

which do not actually transmit traffic pro-

Please note that several buttons have no

grammes themselves, but by using RDS-

function while a traffic announcement is

EON they offer the possibility to receive the

broadcast.

traffic messages broadcast by another traf-

 

fic programme station in the same radio

Warning beep

network.

If you wish to have the priority for traffic an-

If you leave the reception area of the traffic

nouncements activated while listening to

programme station currently tuned into, you

one of these stations (e.g. NDR3), “TA” must

appear on the display panel.

will hear a warning beep after approximate-

ly 30 seconds.

If a traffic announcement is broadcast, the

This alarm tone will also be released when

radio will automatically switch to the linked

pressing a preset button which has no traf-

traffic programme station (in this case,

fic programme allocated to it.

NDR2) for the duration of the message and

 

return to the original programme (NDR3)

 

afterwards.

 

Switching the warning beep off

a)Tune into another station offering traf- fic information:

Press the rocker switch or

press a preset button which has a traffic programme station allocated to it.

Alternatively:

b)Switch off the priority for traffic an- nouncements:

Press TA.

“TA” will disappear from the dis- play.

Automatic seek tuning start

(tape and CD changer operation)

When leaving the reception area of the tuned in traffic programme station while listening to a tape or CD, the system will automatically start searching for a new TA programme.

If no such station is found within approxi- mately 30 seconds, tape or CD operation will be stopped and a warning beep will sound. To switch the warning beep off, pro- ceed as described above.

DEUTSCH ENGLISH FRANÇAIS ITALIANO NEDERLANDS SVENSKA ESPAÑOL PORTUGUÊS

43

Image 18
Contents Heidelberg RCM Page Contents Quick reference Rocker switch Extra rocker switch functionsAUD J GEO DSC Mode H PTY Display Flashing KeyCard tongueMIX MAG MIXMIX CD MIX OFF@ DIS Extra function GEO AUDImportant notes Replacing a KeyCard KeyCard theft protection systemRemoving the KeyCard Never pull out the KeyCard directlyTurn On Message T.O.M Switching off the flashlightShort Additional Memory S.A.M Optical indication for extra securityRadio operation with RDS Radio Data System Storing stations Scrolling through the broad- casting networksChanging the memory bank Automatically storing the stronSwitching from stereo to mono Selecting the seek tuning sensi- tivityPreset Scan Recalling stored stationsProgramme type NewsStoring programme types Scanning stations with PTY-SCANPTY priority Receiving traffic programme stations with RDS-EON Automatic seek tuning startSwitching the warning beep off On/offTape operation Portions with Blank Skip Switching the tape sideScanning cassette titles with Skipping unrecorded tape Dolby B NRCare notes Switching to CDC operationCD changer operation optional Selecting CDs and titlesMIX playback Selecting the display modeStoring the display mode Entering CD namesDSC programming Deleting CD names withColour Scantime AUXOverview of the DSC factory settings SpecificationsAppendix Blaupunkt-Werke GmbH
Related manuals
Manual 31 pages 21.97 Kb Manual 33 pages 27.68 Kb