Blaupunkt RCR 127 Receiving traffic programme stations with RDS-EON, On/off, Beep tone

Page 17

Receiving traffic programme stations with RDS-EON

The abbreviation “EON” stands for En-

Traffic announcement priority

hanced Other Networks, meaning the ex-

on/off

change of information within a radio network.

If the priority for traffic announcement pro-

Many FM broadcasters offer traffic messag-

grammes is activated, “TA” will light up in

es for their service area at regular intervals.

the display.

All traffic programme stations transmit a

To switch the priority on or off:

special carrier signal alongside their pro-

• Press the TA button.

grammes, which is decoded by your car ra-

dio. If this signal is identified, “TP” will ap-

When pressing TA while a message is be-

pear in the display (Traffic Programme).

ing broadcast, this message will be inter-

In addition to these, there are also stations

rupted. The unit will then switch back to the

which do not actually transmit traffic pro-

previous condition. The priority for all other

grammes themselves, but by using RDS-

traffic messages remains active.

EON they offer the possibility to receive the

Please note that several buttons have no

traffic messages broadcast by another traf-

function while a traffic announcement is

fic programme station in the same radio

broadcast.

network.

 

If you wish to have the priority for traffic an-

Beep tone

nouncements activated while listening to

If you leave the reception area of the traffic

one of these stations (e.g. NDR3), “TA” must

appear on the display panel.

programme station currently tuned into, you

If a traffic announcement is broadcast, the

will hear a beep tone approximately every

radio will automatically switch to the linked

30 seconds.

traffic programme station (in this case,

This tone will also be released when press-

NDR2) for the duration of the message and

ing a preset button which has no traffic pro-

return to the original programme (NDR3)

gramme allocated to it.

afterwards.

 

Switching off the beep tone

a)Tune into another station offering traf- fic information:

Press the rocker switch or

press a preset button which has a traffic programme station allocated to it.

Alternatively:

b)Switch off the priority for traffic an- nouncements:

Press TA.

“TA” will disappear from the display.

Automatic seek tuning start

(tape operation)

When leaving the reception area of the tuned in traffic programme station while listening to a tape, the system will automatically start searching for a new TA programme.

If no such station is found within approxi- mately 30 seconds, you will hear a warning beep every 30 seconds. To switch off the beep tone proceed as described above.

DEUTSCH ENGLISH FRANÇAIS ITALIANO NEDERLANDS SVENSKA ESPAÑOL PORTUGUÊS

37

Image 17
Contents Freiburg RCR Montreux RCR Colorado RCR 13 12 Contents Switching on with the ignition being switched off Switching on/off with the on button Press onSwitching on/off via the ignition Quick referenceDSC Mode a Extra rocker switch functionsDisplay KeyCard theft protection system3, 4, 5, 6 preset buttons To switch overTravelstore SRC SourceExtra function Preset ScanCassette loading slot ? SCTraffic safety PrecautionsInstallation AccessoriesKeyCard theft protection system Turn On Message T.O.M Short Additional Memory S.A.MCare of your KeyCard AF Alternative frequency Radio operation with RDS Radio Data SystemREG regional programme Manual tuning with Station tuningAutomatic tuning Changing the memory bank Scanning stored stations with Preset ScanStoring stations Recalling stored stationsSelecting the seek tuning sensi- tivity Switching from stereo to monoScanning stations with Radio- Scan LoudnessSelecting a programme type Checking the programme type of the stationDisplaying the selected programme type Scanning stations with PTY-SCAN Storing programme types PTY priorityReceiving traffic programme stations with RDS-EON Automatic seek tuning startTraffic announcement priority On/offFast Forward/Rewind Tape operationInserting a tape Removing a tapeCare notes Listening to the radio during fast tape winding with RMAM on / OFF Montreux RCR DSC programmingOverview of DSC factory set- tings To quit the DSC programming mode and store the adjustmentAppendix SpecificationsAmplifier TunerBlaupunkt-Werke GmbH
Related manuals
Manual 20 pages 24.65 Kb Manual 19 pages 21.39 Kb