JVC KD-AV7010 manual Auto Surround, Seat Position, Dynamic. Range Compression

Page 50

ENGLISH

AUTO SURROUND

You can activate an appropriate surround mode automatically when a loaded disc is detected.

ON: An appropriate surround/DSP mode is automatically selected.

While Dolby Digital multi-channel signals are detected, “Dolby Digital” is automatically selected.

While DTS multi-channel signals are detected, “DTS” is automatically selected.

While Dolby Surround (PL II) signals are detected, “Dolby Pro Logic II Movie” is automatically selected.

While Linear PCM signals are detected (for DVD/CD), “Dolby Pro Logic II Music” is automatically selected.

While other signals are detected,

Surround mode is defeated.

OFF: Cancels this function.

Auto Surround does not work for any sources other than “DISC.” When another source is selected, the currently selected Surround or DSP mode is resumed (see page 37).

SEAT POSITION

Select the listening seat position where you want to locate the sound image.

Speaker distance and speaker level can be memorized for each position.

FRONT LEFT: For the front left seat.

FRONT RIGHT: For the front right seat.

ALL CENTER: For all front and rear seats.

REAR CENTER: For the rear seats.

: Displays the SPK

DISTANCE screen.

You can adjust the speaker distance from your listening position in meters or feet.

: Displays the SPK

LEVEL screen.

You can adjust the speaker level referring to the test tone.

Emits the test tone from each

speaker in sequence.

To stop, press again.

D (Dynamic). RANGE COMPRESSION

You can enjoy a powerful sound even at a low volume level by compressing dynamic range (difference between the lowest and the highest frequency sounds).

• This takes effect for all the playback sources.

Display sub-setting screens.

50

Image 50
Contents KD-AV7010 Temperature inside the car How to reset your unitFor safety Important for Laser ProductsHow to read this manual EnglishContents Digital audio formats Introduction-Playable DiscsFollowing discs cannot be played back DTS ** Digital Theater SystemsQuick Guide-How to Use the Controls Remote controllerEnglish Main unit front ButtonsPreparation Remote Controller-RM-RK220 To erase and display the Touch Panel icons Ex. Fader/balance adjustmentOperation Methods Ex. DVD playbackUsing the buttons and controls directly ExamplesBasic Operations Adjust the volumeTurn on the power Select the sourceWhile playing any source Setting the clockWhen the unit is turned on Set the clock timeChanging the touch panel color Changing the sourceChanging the graphic screen While playing a disc Displaying the level meterWhile listening to radio FM/AM Radio Operations Back to the beginningSelect the Tuner Select Search ModeWhen an FM stereo broadcast is hard to receive Select a band FM/AM Tune in to a stationStoring stations in memory FM station automatic presetting-SSMManual presetting Strong-station Sequential MemoryTo tune in to a preset station To store a station using the preset listDVD/VCD Operations DVD VCDMP3 CD/MP3 OperationsCD/CD Text Before performing any operations, observe Following Insert a discOperate the disc To resume normal speed, press Remote controller while playing a discOn-screen guide icons To play back the still pictureProhibiting disc ejection On the remote controllerChanging the aspect ratio Selecting MP3 foldersSelect an item, then confirm Operating the disc menuWhile playing a DVD While playing a VCDReplaying the previous scenes To cancel the PBC playbackZooming Move the zoomed-in portion on the monitorSelect a subtitle language you want Selecting subtitlesSelecting audio languages Select an audio language you wantSelecting multi-angle views Select a view angle you wantTo locate a track by displaying the track Locating a folder/track usingList ListRepeat Play Displaying the disc textSelecting playback modes Intro Scan Searching for scenes or songsRandom Play Title/Chapter/Folder/Track SearchTime Search Enter a number, then confirmExamples for DVD Example for VCD/CDSelecting the sources Dual Mode OperationsTo activate Dual Mode and select the subsidiary source Select the subsidiary source SUB you wantTo activate Dual Mode To cancel the Dual Mode, pressAdjust the AV output volume To operate the subsidiary sourceMake adjustment if you want to Surround Mode OperationsActivate and select the surround mode or DSP mode When surround mode is activated When DSP mode is activatedDolby Digital 5.1 CH Surround modesDolby Digital DTS Digital SurroundDSP On Surround Off DSP modeSurround On DSP Off Defeat Surround/DSP OffWhen DSP mode is activated HallSound Modes iEQ Operations Available sound modes Select one of the preset sound iEQ ModesStoring your own sound modes To adjust the input level Other Sound AdjustmentsMake adjustment as you like To adjust fader and balanceAdjustable items Monitor AdjustmentsSelect an item to adjust Adjust the itemSelect the item you want Initial Setup-DVD MenuChange the setting Subtitle Menu LanguageAudio Language Monitor TypeInitial Setup-MONITOR Blind Control Wiring CheckAuto OPEN/CLOSE Beep Tone Initial Setup-ON Screen Select the item you want Change the settingMessage On Screen LanguageGuide ClockInitial Setup-AUDIO MENU/PSM Change the setting or enter the setting screenDynamic. Range Compression Auto SurroundSeat Position AMP Gain Speaker SizeCross Over FM if Filter Dimmer ModeAV2 Input Select Back GearOther Main Functions Assigning titles to the sourcesSelect an unwanted name Enter a name Confirm SourceStations Changing the monitor position Angle Removing the monitorCD Changer Operations Before operating your CD changer Basic CD Changer OperationsSelect CD-CH Operate the disc Selecting disc/folders/tracks Locating a disc/folder/track using the listAdvanced CD Changer Operations Select a disc you wantDisplaying the disc text information To locate a track by displaying the track listRepeat Play Track Searching for songs Folder/Track SearchTo change the aspect ratio External Component OperationsSelect the external source TV Tuner Operations Select TV TV station automatic presetting-Auto MemoryWatching TV programs Tune in to a TV stationSelect a preset number Tune into a TV stationDisplaying the preset list Check your Sirius ID, see Turn on the power Select SAT SiriusSirius Radio Operations Back to the beginning Select a category Listening to the Sirius RadioSelect SAT Sirius Select a channel for listeningTo select a user preset channel using the list Listening to a user preset ChannelTo store a user preset channel using the list While listening to the channel you want To storeWhile listening to a channel To select a category Selecting a category/channel using the listsSkipping channels While listening to the 4th channel on ListSirius ID Changing the satellite setupClock Auto Adjust Time ZoneMaintenance Basic Operations More about This ReceiverOperation Methods Radio OperationsEjecting a disc Changing the sourceStopping play Displaying the disc text informationMP3 Control Sound Mode iEQ Operations Dual Mode OperationsSurround Mode Operations Other Sound AdjustmentsTV Tuner Operations Other Main FunctionsSirius Radio Operations Assigning titles to the sourcesDisc playback-DVD/VCD TroubleshootingFM/AM broadcast Disc playback-CD/CD-R/CD-RWTV tuner operations Initial setup-AUDIO MENU/PSMDisc playback-MP3 CD changer operations Sirius radio operationsGraphic screens Preset iEQ modeAdditional Information Language Codes Code LanguageSpecifications Main unitAbout mistracking Hideaway unitRequired space for the monitor ejection Removing the control panelCall Notas sobre las conexiones eléctricas Be sure to ground each unit to the car’s chassisNotas sobre la instalación de la unidad oculta Remarque sur le montage de l’appareil satelliteSystem Connections Conexiones DEL Sistema Installation Instalación Avant de commencer Before connectingAntes de la conexión Unused La unidad sin usar De l’appareil inutilisés Main unit Unidad principal Appareil principalKV-CR100 JVC DLP DLP JVC