Alpine CDM-7858R Turning Power On and Off, Subwoofer On and Off, Turning Loudness On/Off

Page 7
Press and hold the SETUP button for at least 3 seconds.
Press the g DN or f UP button to select the FM LV (FM LEVEL) mode.

Turning Power On and Off

1 Press the POWER button to turn on the unit.

NOTE

The unit can be turned on by pressing any other button except the eject c button.

The volume level gradually increases to the previous level you were listening to before the unit was turned off.

Press and hold the POWER button again for at least 3 seconds.

NOTE

The very first time the power is turned on, the volume will start from level 12, and the LOUD function will be on in the tuner mode.

Subwoofer On and Off

1 Press and hold the SETUP button for at least 3 seconds.

2 Press the g DN or f UP button to select the SUB-W mode.

3 Press the BAND button to select Subwoofer ON or OFF.

4 After setting is completed, press the SETUP button to return to normal mode.

NOTES

Initial mode is "Subwoofer ON."

Set to "Subwoofer OFF" unless the subwoofer is used.

When the subwoofer is turned on, the subwoofer output level can be adjusted. For more details, refer to the Adjusting Volume/Balance/Fader.

Adjusting Volume/Balance

(Between Left and Right)/Fader

(Between Front and Rear)

1 Press the MODE button repeatedly to choose the desired mode.

Each press changes the modes as follows:

VOL

BAL

FAD

 

 

 

 

 

 

 

 

NOTE

If the 5 or 6 button is not pressed in 5 seconds after selecting the BALANCE and FADER modes, the unit automatically sets in the VOLUME mode.

2 Press the 5 and 6 buttons until the desired sound is obtained in each mode.

Turning Loudness On/Off

Loudness introduces a special low- and high- frequency emphasis at low listening levels. This compensates for the ear's decreased sensitivity to bass and treble sound.

1 Press and hold the LOUD button for at least

2 seconds to activate or deactivate the loudness mode. The display shows "LOUD ON" when the loudness mode is activated.

Adjusting Source Signal Levels

If the difference in volume level between the CD player and FM radio is too great, adjust the FM signal level as follows.

1

2

3 Press the BAND button to select the FM signal level HI (High) or LO (Low) to make the signal levels between the FM band and CD player closer.

4 Press the SETUP button to return to normal mode.

5-EN

Image 7
Contents CDM-7859R CDM-7858R CDM-7856R Alpine CD Changers Give You More Contents Precautions Handling the Detachable Front Panel Attaching the Front Panel Controllable With Remote ControlBasic Operations Detaching the Front PanelTurning Loudness On/Off Turning Power On and OffAdjusting Source Signal Levels Subwoofer On and OffBasic Operation Setting the Bass Control Setting the Treble ControlSwitching the Tuner Mode Setting the AUX ModeChanging Audio Level Display Pattern Automatic Seek Tuning Manual TuningRadio Operations Tuning to Preset Stations Automatic Memory of Station PresetsRecalling Preset RDS Stations Setting RDS Reception Mode and Receiving RDS StationsRDS Operations Receiving Traffic Information PTY Programme Type TuningLight M ← Classics → Other M Receiving Traffic Information While Playing CD or Radio When traffic information stations cannot be receivedPriority News Inserting/Ejecting Disc CD Player OperationNormal Play and Pause RPT RPT ALL OFF Music Sensor Skip Repeat PlayFast Forward and Backward X. Random PlayControlling CD Changer Optional Scanning ProgrammesCase of Difficulty InformationsError SpecificationsPrecautions Installation and ConnectionsRemoval InstallationRear or ConnectionTo prevent external noise from entering the audio system Switched Power Lead Ignition Red