MobileHub™ Link Operation(Optional)
BAND/
TEL. 
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
g f |
| 9 F/SETUP |
|
| DISP/ | |||||||||||
|
|
| Rotary encoder | Preset buttons | TITLE | |||||||||||
|
|
|
|
|
|
|
|
|
|
|
| (1 through 6) |
|
| ||
About MobileHub™ Link
Connect a separately sold junction box and a portable telephone (available from Nokia) to control the incoming and outgoing calls of the portable telephone.
Caution
Even with
For the sake of safety, only incoming calls and
•If a portable telephone is connected, its address book, incoming and outgoing history are downloaded to the junction box.
•Please refer to the instruction manual of the junction box.
Telephone Mode ON/OFF
1 Press and hold BAND/TEL. for at least 2 seconds to turn on the Telephone mode.
To turn off, press BAND/TEL.
See relevant pages for each item.
•Press and hold BAND/TEL. for at least 2 seconds. If a portable telephone is not connected, “NO PHONE” is displayed for about 2 seconds, then the mode returns to the original source mode.
•When the portable telephone is taken off the junction box during an incoming or outgoing call, or during a
•When there is an incoming call while the power of
•Even if the power of the portable telephone is off, when CDA- 9820XM is set to Telephone mode, the power of the portable telephone will be turned on.
•Even if the ACC power of the vehicle is turned off (even if the engine is stopped) during a
•If there is an incoming call during operation (except an outgoing call or talking), operation mode will end and switch to the incoming or talking mode.
•An outgoing call from a portable telephone is also possible. However, you cannot perform different operations at the same time from a portable telephone and
•With a junction box connected outgoing, incoming, and sending history will also be recorded in the portable telephone.
•While telephoning, defeat is set to ON. When the call has finished, the unit returns to your previous setting.
•The telephone volume can be adjusted on the
•While telephoning or receiving incoming calls, press DISP/TITLE 
to show the Network Operator display for 5 seconds.
Incoming Calls
1 Press :/J to receive an incoming call.
2 Press BAND/TEL. to finish a call.
Telephone mode will end and return to the original source mode.
•When the Automatic Calling mode is on, you can talk after 3 seconds of receiving the incoming call. (see “Setting the Automatic Calling” on this page.)
Setting the Automatic Calling
The incoming call can be switched to Automatic Calling or Manual Calling.
1 Press and hold F/SETUP for at least 3 seconds. 2 Select the TEL mode by pressing gor f.
3 Press BAND/TEL. to change to TEL AUTO or TEL MANU.
4 Press F/SETUP to return to normal mode.
•Press BAND/TEL. during an incoming call to disconnect it.
•The initial setting of the factory is TEL MANU.
Calling
Calling by the address book
You can call up the address book registered in the portable telephone to call from.
1 Press and hold BAND/TEL. for at least 2 seconds.
2 Press SEARCH/QS to select PHONE BK (Phone Book) mode.
A list in alphabetic order is displayed.
Retrieving an addressee by Alphabetic Sort List
3 When displaying the Alphabetic Sort List, turn the Rotary encoder or press gor fto select the addressee.
4 Press :/J or Rotary encoder to place a call.
5 Press BAND/TEL. to end the call.
Telephone mode will end and return to the original source mode.