In Case of Difficulty
If you encounter a problem, please turn the power off, then on again. If the unit is still not functioning normally, please review the items in the following checklist. This guide will help you isolate the problem if the unit is at fault. Otherwise, make sure the rest of your system is properly connected or consult your authorized Alpine dealer.
No function or display.
•Vehicle’s ignition is off.
-If connected following the instructions, the unit will not operate with the vehicle’s ignition off.
•Improper power lead connections.
-Check power lead connections.
•Blown fuse.
-Replace the fuse on the battery lead of the unit with the proper value.
Disc playback sound is wavering.
•Moisture condensation in the disc unit.
-Allow enough time for the condensation to evaporate (about 1 hour).
Disc insertion not possible.
•A disc is already in the DVD player.
-Eject the disc and remove it.
•The disc is being improperly inserted.
-
Unable to fast forward or reverse the disc.
•The disc has been damaged.
- Eject the disc and discard it; using a damaged disc in your
unit can cause damage to the mechanism.
Disc playback sound skips due to vibration.
•Improper mounting of the unit.
-Securely
•Disc is very dirty.
-Clean the disc.
•Disc has scratches.
-Change the disc.
•The
-Do not use a commercial available lens cleaner disc.
Consult your nearest ALPINE dealer.
Disc playback sound skips without vibration.
•Dirty or scratched disc.
-Clean the disc; damaged disc should be replaced.
CD-R/CD-RW playback not possible.
•Close session (finalization) has not been performed.
-Perform finalization and attempt playback again.
Error displays
•Mechanical error
-Press c. After the error indication disappears, insert the disc again. If the
problem, consult your nearest ALPINE dealer.
MP3 is not played back.
• Writing error occurred. The CD format is not compatible.
-Make sure the CD has been written in a supported format. Refer to “About MP3/WMA” on pages
Unit does not operate.
•Monitor’s power is not turned on.
-Turn on the monitor’s power.
•Condensation.
-Wait a while (about 1 hour) for the condensation to dry.
No picture is produced.
•Monitor’s mode is not switched to the mode you want to see.
-Switch to the mode you want to see.
•Monitor’s parking brake cord is not connected.
-Connect the monitor’s parking brake cord and set the parking brake. (For details, refer to the monitor’s instructions.)
•Monitor’s parking brake is not set.
-Connect the monitor’s parking brake cord and set the parking
brake. (For details, refer to the monitor’s instructions.)
Playback does not start.
•Disc is loaded
-Check the disc and load it with the labeled side facing upward.
•Disc is dirty.
-Clean the disc.
•A disc not able to playback with this unit is loaded.
-Check if the disc is able to be played back.
•Parental lock is set.
-Cancel the parental lock or change the rating level.
•Setup menu is displayed.
-Press SETUP to turn the menu off.
Picture is unclear or noisy.
•Disc is being
-The picture may be unclear, but this is normal.
•Vehicle’s battery power is weak.
-Check the battery power and wiring.
(The unit may malfunction if the battery power is under 11 volts with a load applied.)
•Monitor’s fluorescent tube is worn out.
-Replace the monitor’s fluorescent tube.
Image stops sometimes.
• Disc is scratched.
- Replace with a
Unable to turn the power off by switching sources on the head unit. (Only when an
•The switched (ignition) power lead for this unit is connected.
-Do not connect the switched (ignition) power lead for this unit when an
Indication
DISC ERROR
•Mechanism error.
1)Press c and eject the CD.
If the disc does not eject, press c again for at least 3 seconds and eject the disc.
If the disc still does not eject, consult your Alpine dealer.
2)When the error indication remains after ejecting, press c again.
If the error indication still does not turn off after pressing c a few times, consult your Alpine dealer.
•The temperature in the car is too low.
- Raise the temperature in the car to normal temperature.
•A disc which contains audio data and JPEG data has been inserted.
- Set the PLAY MODE setting to